CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com
stepping-motor control with PWM and L293D

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
spom



Joined: 12 Jul 2007
Posts: 32

View user's profile Send private message

stepping-motor control with PWM and L293D
PostPosted: Tue Dec 04, 2007 5:07 am     Reply with quote
Hi,

I use a Pic 16F818, a no name bipolar stepping-motor with 50 steps, and a L293D(http://www.ortodoxism.ro/datasheets/texasinstruments/l293d.pdf).

I want to generate a PWM signal with the Pic, and then the motor should rotate 50 steps left, and then 50 steps right.

My code looks that way:

Code:

#include <16f818.h>
#use delay(clock=8000000)
#fuses NOWDT,HS,NOPUT,NOPROTECT,NOBROWNOUT,NOLVP

void main()
{

   setup_timer_2(T2_DIV_BY_4, 149, 1);
   setup_ccp1(CCP_PWM);
   set_pwm1_duty(255L);

while(TRUE)
   {
      output_high(PIN_B0);
      output_low(PIN_B1);

     //50 steps and then turn around????
   }
}


I don't know how to handle it that the motor change rotation after 50 steps.
Is the pwm right?

By the way: one inductor is connected to PIN 2 and 7 of the L293D and the other to PIN 10 and 15. Is that right?

Thanks!
Ttelmah
Guest
PostPosted: Tue Dec 04, 2007 5:17 am     Reply with quote
Basically, no.
The PWM, generates a continuous stream of pulses, allowing you to specify the mark space ratio. It does _not_ count pulses.
Almost exactly this question, was asked a while ago. A search should find it. Look for 'PWM stepper', asking the search to find 'all' terms, and you should get a number of threads about this. The simplest way for what you want,will be to ignore PWM completely.

Best Wishes
spom



Joined: 12 Jul 2007
Posts: 32

View user's profile Send private message

PostPosted: Tue Dec 04, 2007 11:25 am     Reply with quote
Thanks!

But I've still had a problem. I connected one inductor with B0 and B1 of the PIC and the second inductor with B6 and B7 of the PIC.

Now my code:
Code:

#include <16f818.h>
#use delay(clock=8000000)
#fuses NOWDT,HS,NOPUT,NOPROTECT,NOBROWNOUT,NOLVP

main()
{
int sequence[8] = {130,129,65,66};

int i=0;
int16 c=0;

   while(1)
   {
      delay_us(2000);
      output_B(sequence[i]);
      i++;

      if (i>3)
      {
         c++;
         i=0;
      }

      if (c==500)
      {
         c=0;
         delay_ms(1000);
      }
   }
}


But it doesn't work! Why?

Thank you for your help!
Ttelmah
Guest
PostPosted: Tue Dec 04, 2007 3:38 pm     Reply with quote
Try reversing one coil. If you have the phase of one coil reversed, it'll just sit and move back/forwards a tiny amount.

Best Wishes
spom



Joined: 12 Jul 2007
Posts: 32

View user's profile Send private message

PostPosted: Sun Dec 09, 2007 6:38 am     Reply with quote
Sorry for my stupid questions again:

I changed my code accorgding to the example EX_STEP.C from CCS C and therefor my pin assignment:

Code:

#include <16f818.h>
#use delay(clock=8000000)
#fuses NOWDT,HS,NOPUT,NOPROTECT,NOBROWNOUT,NOLVP

#BYTE port_b = 6
#define FOUR_PHASE TRUE

#ifdef FOUR_PHASE
BYTE const POSITIONS[4] = {0b0101,
                           0b1001,
                           0b1010,
                           0b0110};
#else
BYTE const POSITIONS[8] = {0b0101,
                           0b0001,
                           0b1001,
                           0b1000,
                           0b1010,
                           0b0010,
                           0b0110,
                           0b0100};
#endif


drive_stepper(BYTE speed, char dir, BYTE steps)
{
   static BYTE stepper_state = 0;
   BYTE i;

   for(i=0; i<steps; ++i) {
     delay_ms(speed);
     set_tris_b(0xf0);
     port_b = POSITIONS[ stepper_state ];
     if(dir!='R')
       stepper_state=(stepper_state+1)&(sizeof(POSITIONS)-1);
     else
       stepper_state=(stepper_state-1)&(sizeof(POSITIONS)-1);
   }
}

main()
{
   BYTE speed, steps;
   char dir;

   while (TRUE)
   {
       speed = 20;
       dir='F';
       steps = 168;

       drive_stepper(speed,dir,steps);
   }
}

But the motor doesn't rotate. I feel an easy movement, but not 7.5°.
The contacts are right as the power supply fall down after switching on. So the motor need current.
Where is the fault?

Thanks!
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group