CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support
ERRORS option in the USE RS232 with PIC16F648A

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
epotama
Guest
ERRORS option in the USE RS232 with PIC16F648A
PostPosted: Fri Oct 03, 2003 7:24 am     Reply with quote
I use a PIC16F628A & PIC16F648A with PCWH3.178.

PIC16F628A with
#users232(baud=19200,parity=E,xmit=PIN_B2,rcv=PIN_B1,bits=8,BRGH1OK,ERRORS)
-----------> No error,OK.

But,
PIC16F648A with
#users232(baud=19200,parity=E,xmit=PIN_B2,rcv=PIN_B1,bits=8,BRGH1OK,ERRORS)
An error appears in the following line.
Line-------> if (bit_test(RS232_ERRORS,0) == 0)

-----------> An error message of
" Undefined identifier RS232_ERRORS"
comes out in line of program file. and BUILD FAILED.

Why can't I use ERRORS option in the USE RS232 with PIC16F648A ?
Why no error with PIC16F628A ?
Give me an advice, please.
Haplo



Joined: 06 Sep 2003
Posts: 659
Location: Sydney, Australia

View user's profile Send private message

PostPosted: Fri Oct 03, 2003 8:09 am     Reply with quote
As far as I can remember you can only use ERRORS with the hardware serial port. Change the send and receive pins to RC6 and RC7, and the compiler error should go away.
epotama
Guest
PostPosted: Fri Oct 03, 2003 8:27 am     Reply with quote
Haplo wrote:
As far as I can remember you can only use ERRORS with the hardware serial port. Change the send and receive pins to RC6 and RC7, and the compiler error should go away.


Thank you for the advice!
But PIC16F648A ,it has a hardware serial port.
and send pins is RB2 and receive pins is RB1.
PIC16F628A is the same, too.
No error with PIC16F628A.
But an error with PIC16F648A.
Why?
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Fri Oct 03, 2003 5:03 pm     Reply with quote
It looks like there is a problem with the Device data for the 16F648A.
I don't think it has a hardware USART listed as available for that chip.
If you have PCW, then you have the Device Editor, and you should be
able to fix this. Otherwise, I think you have to report it to CCS and
hope that they will email you an updated Device.dat file.

(I tested this with PCM vs. 3.176)
Guest
PostPosted: Fri Oct 03, 2003 6:44 pm     Reply with quote
PCM programmer wrote:
(I tested this with PCM vs. 3.176)


Thank you very much for trying!
Still an error appeared.
It found out that it was not only my problem.
As a matter of fact, I take out the mail of the question about this problem to CCS.
Yet, a final answer hasn't been able to get it.
But, it was said by the latest mail that they could compile it.

Thanks to you, it found that it was not only my problem.
So, I take out mail to CCS again this problem is not only my problem.

Thank you for sparing precious time for me.
epotama
Guest
PostPosted: Fri Oct 03, 2003 7:08 pm     Reply with quote
I am sorry,I forgot to write a name.
An upper message is mine.
epotama
Guest
PostPosted: Sat Oct 04, 2003 6:25 pm     Reply with quote
I report it,
This problem was solved by using two files that it was sent by CCS.

devices.dat and pcm.dll

If there is a person worried about the same problem,
it is good when it mails CCS and has a file sent.
Krapf



Joined: 09 Oct 2003
Posts: 1
Location: Brasil

View user's profile Send private message ICQ Number

PostPosted: Thu Oct 09, 2003 9:42 am     Reply with quote
epotama wrote:
I report it,
This problem was solved by using two files that it was sent by CCS.


Is there a way to get those files directly from you without wait for CCS response?
I just found out that PCM compiler does not use the USART available, NEVER, it makes all functions by software.
(this explains why ERROR functions are not available)

thanks
_________________
Rafael Krapf
Elo Sistemas Eletronicos SA
Brasil
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group