CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support

12F1822 PWM problem
Goto page 1, 2, 3  Next
 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
ads



Joined: 09 May 2020
Posts: 11

View user's profile Send private message

12F1822 PWM problem
PostPosted: Sat May 09, 2020 5:00 pm     Reply with quote

Hi I am having a problem with defining this only :

Code:
#include <12F1822.h>
#fuses NOMCLR INTRC_IO PLL_SW
#use delay(clock=32000000)
#use fast_io(A)
#use pwm (PWM1, FREQUENCY = 38KHz, DUTY = 25, PWM_OFF)


Which says
***Error 44 "main.c" Line 10(5,52): Internal Error - Contact CCS PPUSE

Line 10 is this line:
Code:
#use pwm (PWM1, FREQUENCY = 38KHz, DUTY = 25, PWM_OFF)


Does anyone has any idea what should be done to fix this. What is wrong with definition of pwm.
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sat May 09, 2020 6:00 pm     Reply with quote

It compiled OK for me. I'm using CCS vs. 5.093.
Quote:

Compiling C:\...\pcm_test on 09-May-20 at 16:58
More info: PWM period: 26.38 us, Frequency: 37.915 kHz, Resolution: 10.00 bits
Memory usage: ROM=1% RAM=4% - 12%
0 Errors, 0 Warnings.
Build Successful.
Loaded C:\...\pcm_test.cof.
BUILD SUCCEEDED: Sat May 09 16:58:35 2020
ads



Joined: 09 May 2020
Posts: 11

View user's profile Send private message

PostPosted: Sun May 10, 2020 6:12 am     Reply with quote

PCM programmer wrote:
It compiled OK for me. I'm using CCS vs. 5.093.
Quote:

Compiling C:\...\pcm_test on 09-May-20 at 16:58
More info: PWM period: 26.38 us, Frequency: 37.915 kHz, Resolution: 10.00 bits
Memory usage: ROM=1% RAM=4% - 12%
0 Errors, 0 Warnings.
Build Successful.
Loaded C:\...\pcm_test.cof.
BUILD SUCCEEDED: Sat May 09 16:58:35 2020


Then it is because of my compiler. Do you think can I define my own use pwm function.
temtronic



Joined: 01 Jul 2010
Posts: 9215
Location: Greensville,Ontario

View user's profile Send private message

PostPosted: Sun May 10, 2020 6:33 am     Reply with quote

You should post your compiler version.
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sun May 10, 2020 6:58 am     Reply with quote

ads wrote:
Do you think can I define my own use pwm function ?

Use the normal method, as shown below. This works with CCS vs. 5.093:
Code:
#include <12F1822.h>
#use delay(internal=4M)

//========================
void main()
{

// This puts PWM on Pin A2.
setup_ccp1(CCP_PWM);
setup_timer_2(T2_DIV_BY_1, 255, 1);
set_pwm1_duty(128);  // 50% duty cycle

while(TRUE);
}


If it doesn't work, then post your CCS compiler version.
ads



Joined: 09 May 2020
Posts: 11

View user's profile Send private message

PostPosted: Sun May 24, 2020 12:30 pm     Reply with quote

Hi. Sorry for late reply. My compiler version is 5.008 and I found it if I write the code as
Code:
#use pwm (PWM1, FREQUENCY = 38KHz, DUTY = 25)

(by deleting last command which is PWM_OFF then it compiles. But I don't know if it will work? Do you have any idea the whole code is:

Code:
// Extended NEC protocol IR remote control transmitter CCS C code
 
#include <12F1822.h>
#fuses NOMCLR INTRC_IO PLL_SW
#use delay(clock=32000000)
#use fast_io(A)
#use pwm (PWM1, FREQUENCY = 38KHz, DUTY = 25, PWM_OFF)
 
void send_signal(unsigned int32 number){
  int8 i;
  // Send 9ms burst
  pwm_on();
  delay_ms(9);
  // Send 4.5ms space
  pwm_off();
  delay_us(4500);
  // Send data
  for(i = 0; i < 32; i++){
    // If bit is 1 send 560us pulse and 1680us space
    if(bit_test(number, 31 - i)){
      pwm_on();
      delay_us(560);
      pwm_off();
      delay_us(1680);
    }
    // If bit is 0 send 560us pulse and 560us space
    else{
      pwm_on();
      delay_us(560);
      pwm_off();
      delay_us(560);
    }
  }
  // Send end bit
  pwm_on();
  delay_us(560);
  pwm_off();
  delay_us(560);
}
void main() {
  setup_oscillator(OSC_8MHZ | OSC_PLL_ON);  // Set internal oscillator to 32MHz (8MHz and PLL)
  output_a(0);
  set_tris_a(0x3B);   // Configure RA2 pin as output and others as inputs
  port_a_pullups(0x3B);  // Enable internal pull-ups for pins RA0,RA1,RA3,RA4 & RA5
  while(TRUE){
    while(!input(PIN_A0)){
      send_signal(0x40BF00FF);
      delay_ms(500);
    }
    while(!input(PIN_A1)){
      send_signal(0x40BF807F);
      delay_ms(500);
    }
    while(!input(PIN_A3)){
      send_signal(0x40BF40BF);
      delay_ms(500);
    }
    while(!input(PIN_A4)){
      send_signal(0x40BF20DF);
      delay_ms(500);
    }
    while(!input(PIN_A5)){
      send_signal(0x40BFA05F);
      delay_ms(500);
    }
  }
}



from https://simple-circuit.com/ir-remote-control-transmitter-receiver-ccs-c/
Ttelmah



Joined: 11 Mar 2010
Posts: 19477

View user's profile Send private message

PostPosted: Mon May 25, 2020 2:48 am     Reply with quote

The only person who can really tell is you. Try it.

However, comments:
Just use the standard format as shown by PCM. This is the older
'traditional' way of controlling the PWM.
For pwm_off, just use:

set_pwm1_duty(0L); // Turn output off

For pwm_on, use:

set_pwm1_duty(52); // On, 25% duty. (for your 38KHz)

Your compiler was at best a 'beta' V5 compiler. I didn't even keep the
compiler versions at this point, since they had so many problems.
However far more of the older V4 commands are likely to work than
the V5 ones. This is why using the older PWM syntax is much more
likely to be successful.

So for close to 38KHz:

setup_ccp1(CCP_PWM);
setup_timer_2(T2_DIV_BY_1, 209, 1);
set_pwm1_duty(0); // pwm_off

This gives 38.095KHz, which if the closest the PWM can actually 'do' from
4MHz. Obviously 'no output', since I am turning the pwm off at this
point.
ads



Joined: 09 May 2020
Posts: 11

View user's profile Send private message

PostPosted: Mon May 25, 2020 5:22 pm     Reply with quote

Thanks a lot for all your comments. It works with 'traditional' way Smile.
Denny9167



Joined: 15 Feb 2021
Posts: 49

View user's profile Send private message Send e-mail

PostPosted: Mon Mar 08, 2021 8:52 am     Reply with quote

ads wrote:
Hi. Sorry for late reply. My compiler version is 5.008 and I found it if I write the code as
Code:
#use pwm (PWM1, FREQUENCY = 38KHz, DUTY = 25)

(by deleting last command which is PWM_OFF then it compiles. But I don't know if it will work? Do you have any idea the whole code is:

Code:
// Extended NEC protocol IR remote control transmitter CCS C code
 
#include <12F1822.h>
#fuses NOMCLR INTRC_IO PLL_SW
#use delay(clock=32000000)
#use fast_io(A)
#use pwm (PWM1, FREQUENCY = 38KHz, DUTY = 25, PWM_OFF)
 
void send_signal(unsigned int32 number){
  int8 i;
  // Send 9ms burst
  pwm_on();
  delay_ms(9);
  // Send 4.5ms space
  pwm_off();
  delay_us(4500);
  // Send data
  for(i = 0; i < 32; i++){
    // If bit is 1 send 560us pulse and 1680us space
    if(bit_test(number, 31 - i)){
      pwm_on();
      delay_us(560);
      pwm_off();
      delay_us(1680);
    }
    // If bit is 0 send 560us pulse and 560us space
    else{
      pwm_on();
      delay_us(560);
      pwm_off();
      delay_us(560);
    }
  }
  // Send end bit
  pwm_on();
  delay_us(560);
  pwm_off();
  delay_us(560);
}
void main() {
  setup_oscillator(OSC_8MHZ | OSC_PLL_ON);  // Set internal oscillator to 32MHz (8MHz and PLL)
  output_a(0);
  set_tris_a(0x3B);   // Configure RA2 pin as output and others as inputs
  port_a_pullups(0x3B);  // Enable internal pull-ups for pins RA0,RA1,RA3,RA4 & RA5
  while(TRUE){
    while(!input(PIN_A0)){
      send_signal(0x40BF00FF);
      delay_ms(500);
    }
    while(!input(PIN_A1)){
      send_signal(0x40BF807F);
      delay_ms(500);
    }
    while(!input(PIN_A3)){
      send_signal(0x40BF40BF);
      delay_ms(500);
    }
    while(!input(PIN_A4)){
      send_signal(0x40BF20DF);
      delay_ms(500);
    }
    while(!input(PIN_A5)){
      send_signal(0x40BFA05F);
      delay_ms(500);
    }
  }
}



from https://simple-circuit.com/ir-remote-control-transmitter-receiver-ccs-c/



I’m having same problem with code as-is,
It may have worked using an older version of CCS, but not with newest, which I have. I’ll try some of the suggestions quoted here. Thanks

I’m a newby BtW so I’m still learning.
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Mon Mar 08, 2021 6:29 pm     Reply with quote

I tested this in hardware with the code you posted and it's putting out
pulses on pin A2 (pin 5 on the DIP8 PIC package). That's correct.
I tested this on a Microchip Low Pin Count board with a 12F1822 and
CCS vs. 5.103.

To measure the frequency, I modified the main() by adding the two lines
shown in bold below. I got a freq of 37.91 on my scope with 25% duty
cycle. That's correct.
Quote:
void main() {
setup_oscillator(OSC_8MHZ | OSC_PLL_ON);
output_a(0);
set_tris_a(0x3B);
port_a_pullups(0x3B);

pwm_on();
while(TRUE);


I don't have an NEC TV to test it with. If you look at his while() loop,
he has buttons on pins A0, A1, A3, A4, A5. These buttons connect ground
to the PIC pins if they are pressed. The pullups are provided by the PIC
as shown in his code above.

You will need this button circuit on each of the 5 pins listed above:
Code:

           ___  Pushbutton Switch 
To        _|_|_
PIC ------o   o------
pin                 |             
                   --- GND
                    -
Denny9167



Joined: 15 Feb 2021
Posts: 49

View user's profile Send private message Send e-mail

PostPosted: Mon Mar 08, 2021 10:38 pm     Reply with quote

PCM programmer wrote:
I tested this in hardware with the code you posted and it's putting out
pulses on pin A2 (pin 5 on the DIP8 PIC package). That's correct.
I tested this on a Microchip Low Pin Count board with a 12F1822 and
CCS vs. 5.103.

To measure the frequency, I modified the main() by adding the two lines
shown in bold below. I got a freq of 37.91 on my scope with 25% duty
cycle. That's correct.
Quote:
void main() {
setup_oscillator(OSC_8MHZ | OSC_PLL_ON);
output_a(0);
set_tris_a(0x3B);
port_a_pullups(0x3B);

pwm_on();
while(TRUE);


I don't have an NEC TV to test it with. If you look at his while() loop,
he has buttons on pins A0, A1, A3, A4, A5. These buttons connect ground
to the PIC pins if they are pressed. The pullups are provided by the PIC
as shown in his code above.

You will need this button circuit on each of the 5 pins listed above:
Code:

           ___  Pushbutton Switch 
To        _|_|_
PIC ------o   o------
pin                 |             
                   --- GND
                    -


Thanks, I followed some of your suggestions, by adding them to the MAIN:



setup_ccp1(CCP_PWM);
setup_timer_2(T2_DIV_BY_1,209,1);

Got a successful build, 0=errors,0=warnings


I’ll program tomorrow and try it out. I’m also working on the RX as well.

I build audio equipment for a living and I’m wanting to build a remote system for a preamplifier, I thought this would be a good solution.
Denny9167



Joined: 15 Feb 2021
Posts: 49

View user's profile Send private message Send e-mail

PostPosted: Mon Mar 08, 2021 10:42 pm     Reply with quote

PCM programmer wrote:
I tested this in hardware with the code you posted and it's putting out
pulses on pin A2 (pin 5 on the DIP8 PIC package). That's correct.
I tested this on a Microchip Low Pin Count board with a 12F1822 and
CCS vs. 5.103.

To measure the frequency, I modified the main() by adding the two lines
shown in bold below. I got a freq of 37.91 on my scope with 25% duty
cycle. That's correct.
Quote:
void main() {
setup_oscillator(OSC_8MHZ | OSC_PLL_ON);
output_a(0);
set_tris_a(0x3B);
port_a_pullups(0x3B);

pwm_on();
while(TRUE);


I don't have an NEC TV to test it with. If you look at his while() loop,
he has buttons on pins A0, A1, A3, A4, A5. These buttons connect ground
to the PIC pins if they are pressed. The pullups are provided by the PIC
as shown in his code above.

You will need this button circuit on each of the 5 pins listed above:
Code:

           ___  Pushbutton Switch 
To        _|_|_
PIC ------o   o------
pin                 |             
                   --- GND
                    -



Do you use the low or high power IR emitters? just curious.
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Tue Mar 09, 2021 12:43 am     Reply with quote

Denny9167 wrote:

I’m having same problem with code as-is,
It may have worked using an older version of CCS, but not
with newest, which I have.

I followed some of your suggestions, by adding them to the MAIN:

setup_ccp1(CCP_PWM);
setup_timer_2(T2_DIV_BY_1,209,1);

Got a successful build, 0=errors,0=warnings

If you had to add those two lines to get a successful build, then you don't
have the newest version of the compiler, which is vs. 5.103. You can see
the version that you have by looking at the top of the .LST file.
Code:

CCS PCM C Compiler, Version 5.103, xxxxx       08-Mar-21 22:42

Filename:   C:\...\Projects\PCM_Test\PCM_TEST.lst

               ROM used:   295 words (14%)
                           Largest free fragment is 1753
               RAM used:   6 (5%) at main() level
                           23 (18%) worst case
               Stack used: 2 locations
               Stack size: 16

I didn't change anything in the code you posted, and it compiled fine with
vs. 5.103. Here is a link to your post:
http://www.ccsinfo.com/forum/viewtopic.php?t=58717&start=8
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Tue Mar 09, 2021 12:44 am     Reply with quote

Denny9167 wrote:

Do you use the low or high power IR emitters? just curious.

I have not assembled a board. I am just helping you with the code, and
the PWM operation of the PIC. I don't know which IR emitter is best.
Denny9167



Joined: 15 Feb 2021
Posts: 49

View user's profile Send private message Send e-mail

PostPosted: Tue Mar 09, 2021 5:59 am     Reply with quote

PCM programmer wrote:
Denny9167 wrote:

Do you use the low or high power IR emitters? just curious.

I have not assembled a board. I am just helping you with the code, and
the PWM operation of the PIC. I don't know which IR emitter is best.


Appreciate it very much!
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Goto page 1, 2, 3  Next
Page 1 of 3

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group