CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com

LCD&hd44780 don't run with driver <lcd.c> and 16F8

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
nanard-bis
Guest







LCD&hd44780 don't run with driver <lcd.c> and 16F8
PostPosted: Fri Jan 24, 2003 9:14 am     Reply with quote

Hello,

I connect PORT D 16lf877 at lcd(HD44780)
and the ttl signal d7...d4 is not clear
with the scope. A peak appear on 0v and 5V
when i use the driver #include<lcd.c>.
I don't know why this configuration don't run
(16lf877,port d , mode 4 bit for the hd44780)
my code.
Thank you for you help

#include <16F877.H>
#device PIC16F877 10 bit ADC=10/*declaration pour lire ADRESH et ADRESL*/
#use delay (clock=1500000)/*declare le quartz du µc*/
#include <lcd.c>
main()
{
do
{
lcd_init();
delay_ms(2000);
lcd_putc("\fReady");
delay_ms(2000);
}
while( 1 );
}
___________________________
This message was ported from CCS's old forum
Original Post ID: 10967
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

Re: LCD&hd44780 don't run with driver <lcd.c> and
PostPosted: Fri Jan 24, 2003 4:52 pm     Reply with quote

:=Hello,
:=
:=I connect PORT D 16lf877 at lcd(HD44780)
:=and the ttl signal d7...d4 is not clear
:=with the scope. A peak appear on 0v and 5V
:=when i use the driver #include<lcd.c>.
:=I don't know why this configuration don't run
:=(16lf877,port d , mode 4 bit for the hd44780)
:=my code.
--------------------------------------------------------
I assume you're working with the board member called "isa".
He posted a modified version of the CCS lcd.c file here:
<a href="http://www.pic-c.com/forum/general/posts/10948.html" TARGET="_blank">http://www.pic-c.com/forum/general/posts/10948.html</a>

He has changed the file in several places, from
"set_tris_b()" to "set_tris_d()". That's OK.

But he forgot to change a very important line.
He left this line unchanged:

#byte lcd = 6 // This puts the entire structure
// on to port B (at address 6)

He should change it to be:

#byte lcd = 8 // This puts the entire structure
// on to port D (at address 8)

So if you are working with ISA, then I assume you will
have the same error in your file. If you fix it, it
should work.
___________________________
This message was ported from CCS's old forum
Original Post ID: 10981
nanard-bis
Guest







Re: LCD&hd44780 don't run with driver <lcd.c> and
PostPosted: Mon Jan 27, 2003 7:53 am     Reply with quote

I don't understand it' s don't work.
Nothing appear.
my code

#include <16F877.H>
#device PIC16F877 10 bit ADC=10/*declaration pour lire ADRESH et ADRESL*/
#use delay (clock=4000000)/*declare le quartz du µc*/
#include <lcd.c>

main()
{
do
{
lcd_init();
delay_ms(100);
lcd_putc('A');
delay_ms(100);
}
while( 1 );
}

and lcd.c modify for port d

// As defined in the following structure the pin connection is as follows:
// D0 enable
// D1 rs
// D2 rw
// D4 D4
// D5 D5
// D6 D6
// D7 D7
//
// LCD pins D0-D3 are not used and PIC D3 is not used.

// Un-comment the following define to use port B
// #define use_portb_lcd TRUE


struct lcd_pin_map { // This structure is overlayed
boolean enable; // on to an I/O port to gain
boolean rs; // access to the LCD pins.
boolean rw; // The bits are allocated from
boolean unused; // low order up. ENABLE will
int data : 4; // be pin B0.
} lcd;




#byte lcd = 8 // on to port D (at address 8)



#define lcd_type 2 // 0=5x7, 1=5x10, 2=2 lines
#define lcd_line_two 0x40 // LCD RAM address for the second line


byte CONST LCD_INIT_STRING[4] = {0x20 | (lcd_type << 2), 0xc, 1, 6};
// These bytes need to be sent to the LCD
// to start it up.


// The following are used for setting
// the I/O port direction register.

STRUCT lcd_pin_map const LCD_WRITE = {0,0,0,0,0}; // For write mode all pins are out
STRUCT lcd_pin_map const LCD_READ = {0,0,0,0,15}; // For read mode data pins are in




byte lcd_read_byte() {
byte low,high;
set_tris_d(LCD_READ);
lcd.rw = 1;
delay_cycles(1);
lcd.enable = 1;
delay_cycles(1);
high = lcd.data;
lcd.enable = 0;
delay_cycles(1);
lcd.enable = 1;
delay_us(1);
low = lcd.data;
lcd.enable = 0;
set_tris_d(LCD_WRITE);
return( (high<<4) | low);
}


void lcd_send_nibble( byte n ) {
lcd.data = n;
delay_cycles(1);
lcd.enable = 1;
delay_us(2);
lcd.enable = 0;
}


void lcd_send_byte( byte address, byte n ) {

lcd.rs = 0;
while ( bit_test(lcd_read_byte(),7) ) ;
lcd.rs = address;
delay_cycles(1);
lcd.rw = 0;
delay_cycles(1);
lcd.enable = 0;
lcd_send_nibble(n >> 4);
lcd_send_nibble(n & 0xf);
}


void lcd_init() {
byte i;
set_tris_d(LCD_WRITE);
lcd.rs = 0;
lcd.rw = 0;
lcd.enable = 0;
delay_ms(15);
for(i=1;i<=3;++i) {
lcd_send_nibble(3);
delay_ms(5);
}
lcd_send_nibble(2);
for(i=0;i<=3;++i)
lcd_send_byte(0,LCD_INIT_STRING[i]);
}


void lcd_gotoxy( byte x, byte y) {
byte address;

if(y!=1)
address=lcd_line_two;
else
address=0;
address+=x-1;
lcd_send_byte(0,0x80|address);
}

void lcd_putc( char c) {
switch (c) {
case '\f' : lcd_send_byte(0,1);
//delay_ms(2);
break;
case '\n' : lcd_gotoxy(1,2); break;
case '\b' : lcd_send_byte(0,0x10); break;
default : lcd_send_byte(1,c); break;
}
}

char lcd_getc( byte x, byte y) {
char value;

lcd_gotoxy(x,y);
lcd.rs=1;
value = lcd_read_byte();
lcd.rs=0;
return(value);
}
___________________________
This message was ported from CCS's old forum
Original Post ID: 11029
nanard-bis
Guest







THANK YOU, thank you it' work
PostPosted: Mon Jan 27, 2003 8:18 am     Reply with quote

the caractere 'A' appear on my display.
After modify set_tris_b at set_tris_d
and adress lcd 8 and after move adjust contrast.



/*****************************************************************************/
/*16F877 4 signale d'horloge reglabe par 4 registres*/
/*Controlé par
/*RX de la RS232 geré par interruption*/
/*horloge quartz de 12Mhz*/
/*******************/


#include <16F877.H>
#device PIC16F877 10 bit ADC=10/*declaration pour lire ADRESH et ADRESL*/
#use delay (clock=4000000)/*declare le quartz du µc*/
#include <lcd.c>


main()
{
do
{
lcd_init();
delay_ms(100);
lcd_putc('A');
delay_ms(100);
}
while( 1 );
}
___________________________
This message was ported from CCS's old forum
Original Post ID: 11030
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group