 |
 |
| View previous topic :: View next topic |
| Author |
Message |
specialk
Joined: 12 Nov 2005
Posts: 27
|
| Laipac RF-24G / TXRX24G 2.4GHz Wireless Transceiver Driver |
 Posted: Sat Jan 21, 2006 12:47 pm |
 |
|
Works well with my configuration
| Code: | ////////////////////////////////////////////////////////////////////////////////
// Laipac RF-24G / TXRX24G
// 2.4GHz Wireless Transceiver Driver
//
// Original by micro222@yahoo.com
//
// Filenmae : RF-24G.c
// Programmer : Steven Cholewiak, www.wahoo-wa.net
// Version : Version 1.0 - 01/21/2006
// Remarks : Datasheets for RF-24G / TXRX24G are available from:
// http://www.sparkfun.com/datasheets/RF/RF-24G_datasheet.pdf
// http://www.sparkfun.com/datasheets/RF/RF-24G.pdf
// http://www.sparkfun.com/datasheets/RF/nRF2401rev1_1.pdf
// http://store.qkits.com/moreinfo.cfm/txrx24g.pdf
//
// This code is modified from the original to support more
// configuration options with more information provided about
// each configuration byte.
////////////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////
//Pin Configuration
//
// Pin Name Pin funtion Description
// 1 GND Power Gound (0V)
// 2 CE Input Chip Enable activates RX or TX mode
// 3 CLK2 I/O Clock output/input for RX data channel 2
// 4 CS Input Chip Select activates Configuration mode
// 5 CLK1 I/O Clock Input(TX)&I/O(RX) for data channel 1 3-wire interface
// 6 DATA I/O RX data channel 1/TX data input /3-wire interface
// 7 DR1 Output RX data ready at data channel 1 (ShockBurst only)
// 8 DOUT2 Output RX data channel 2
// 9 DR2 Output RX data ready at data channel 2 (ShockBurst only)
// 10 VCC Power Power Supply (+3V DC)
#define RF_24G_CE PIN_A5
#define RF_24G_DATA PIN_A4
#define RF_24G_CLK1 PIN_A3
//#define RF_24G_CLK2 PIN_B0
#define RF_24G_DR1 PIN_A2
#define RF_24G_CS PIN_A1
//#define RF_24G_DOUT2 PIN_B4
//#define RF_24G_DR2 PIN_B7
////////////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////
//Configuration Bytes
//
//Bytes 14-02: Shockburst Configuration
//Bytes 01-00: General Device Configuration
//Byte 14: Length of data payload section RX channel 2 in bits
// The total number of bits in a ShockBurst RF package may not exceed 256!
// Maximum length of payload section is hence given by:
// DATAx_W(bits) = 256 - ADDR_W - CRC
#define DATA2_W 32 //4 Bytes
//Byte 13: Length of data payload section RX channel 1 in bits
#define DATA1_W 32 //4 Bytes
//Byte 12-08: Channel 2 Address
#define ADDR2_4 0x00
#define ADDR2_3 0x00
#define ADDR2_2 0x00
#define ADDR2_1 0x42
#define ADDR2_0 0x42
//Byte 07-03: Channel 1 Address
#define ADDR1_4 0x00
#define ADDR1_3 0x00
#define ADDR1_2 0x00
#define ADDR1_1 0x42
#define ADDR1_0 0x42
//Byte 02
// Bit 07-02: ADDR_W - Number of address bits (both RX channels)
// Maximum number of address bits is 40 (5 bytes)
// Bit 01: CRC_L - 8 or 16 bits CRC
// Bit 00: CRC_EN - Enable on-chip CRC generation/checking
// Combine (via |) together constants from each group
// 0b76543210
#define ADDR_W_5_BYTE 0b10100000
#define ADDR_W_4_BYTE 0b10000000
#define ADDR_W_3_BYTE 0b01100000
#define ADDR_W_2_BYTE 0b01000000
#define ADDR_W_1_BYTE 0b00100000
#define CRC_L_8_BIT 0b00000000
#define CRC_L_16_BIT 0b00000010
#define CRC_EN_DISABLE 0b00000000
#define CRC_EN_ENABLE 0b00000001
//Byte 01
// Bit 07: RX2_EN - Enable two channel receive mode
// Bit 06: CM - Communication mode ( Direct or ShockBurst)
// Bit 05: RFDR_SB - RF data rate (1Mbps requires 16MHz crystal)
// Bit 04-02: XO_F - Crystal frequency (Factory default 16MHz crystal mounted)
// Bit 01-00: RF_PWR - RF output power
// Combine (via |) together constants from each group
// 0b76543210
#define RX2_EN_DISABLE 0b00000000
#define RX2_EN_ENABLE 0b10000000
#define CM_DIRECT 0b00000000
#define CM_SHOCKBURST 0b01000000
#define RFDR_SB_250_KBPS 0b00000000
#define RFDR_SB_1_MBPS 0b00100000
#define XO_F_4MHZ 0b00000000
#define XO_F_8MHZ 0b00000100
#define XO_F_12MHZ 0b00001100
#define XO_F_16MHZ 0b00001100
#define XO_F_20MHZ 0b00010000
#define RF_PWR_N20DB 0b00000000 // -20db
#define RF_PWR_N10DB 0b00000001 // -10db
#define RF_PWR_N5DB 0b00000010 // -5db
#define RF_PWR_0DB 0b00000011 // 0db (Full Power)
//Byte 01
// Bit 07-01: RF_CH# - Frequency channel (2400MHz + RF_CH# * 1.0MHz)
// Bit 00: RXEN - RX or TX operation
// Combine (via |) together constants from each group
// 0b76543210
#define RF_CH 0b10000000 // 64 - 2464GHz
#define RXEN_TX 0b00000000
#define RXEN_RX 0b00000001
////////////////////////////////////////////////////////////////////////////////
#inline
RF_24G_initPorts() {
PORT_B_PULLUPS(FALSE);
DISABLE_INTERRUPTS(INT_RB);
}
#define BUF_MAX 4
byte buf[BUF_MAX];
#define CLKDELAY() delay_us(1)
#define CSDELAY() delay_us(10)
#define PWUPDELAY() delay_ms(3)
void putByte( byte b ) { //MSB bit first
int8 i;
int8 p = 7;
for(i=0 ; i < 8 ; i++) {
OUTPUT_LOW(RF_24G_CLK1);
if( BIT_TEST(b,p--) ) {
OUTPUT_HIGH(RF_24G_DATA);
}else{
OUTPUT_LOW(RF_24G_DATA);
}
CLKDELAY();
OUTPUT_HIGH(RF_24G_CLK1); // Clock out on rising edge
CLKDELAY();
}
}
byte getByte() { //MSB bit first
int8 i , b = 0;
int8 p = 7;
for(i=0 ; i < 8 ; i++) {
OUTPUT_LOW(RF_24G_CLK1);
CLKDELAY();
OUTPUT_HIGH(RF_24G_CLK1);
CLKDELAY(); // Read before falling edge
if( INPUT(RF_24G_DATA) ) {
BIT_SET(b,p--);
}else{
BIT_CLEAR(b,p--);
}
}
return b;
}
void RF_24G_Config() {
OUTPUT_LOW(RF_24G_CE);
OUTPUT_LOW(RF_24G_CS);
OUTPUT_LOW(RF_24G_CLK1);
OUTPUT_LOW(RF_24G_DATA);
PWUPDELAY();
OUTPUT_HIGH(RF_24G_CS);
CSDELAY();
//MSB byte first
putByte(DATA2_W);
putByte(DATA1_W);
putByte(ADDR2_4);
putByte(ADDR2_3);
putByte(ADDR2_2);
putByte(ADDR2_1);
putByte(ADDR2_0);
putByte(ADDR1_4);
putByte(ADDR1_3);
putByte(ADDR1_2);
putByte(ADDR1_1);
putByte(ADDR1_0);
putByte(ADDR_W_2_BYTE | CRC_L_16_BIT | CRC_EN_ENABLE);
putByte(RX2_EN_DISABLE | CM_SHOCKBURST | RFDR_SB_1_MBPS | XO_F_16MHZ | RF_PWR_0DB);
putByte(RF_CH | RXEN_RX);
OUTPUT_FLOAT(RF_24G_DATA);
OUTPUT_LOW(RF_24G_CE);
OUTPUT_LOW(RF_24G_CS);
OUTPUT_LOW(RF_24G_CLK1);
}
void RF_24G_SetTxByte() {
OUTPUT_LOW(RF_24G_CE);
OUTPUT_HIGH(RF_24G_CS);
CSDELAY();
putByte(RF_CH | RXEN_TX);
OUTPUT_LOW(RF_24G_CS);
OUTPUT_LOW(RF_24G_CLK1);
}
void RF_24G_SetTx() {
// Once the wanted protocol, modus and RF channel are set,
// only one bit (RXEN) is shifted in to switch between RX and TX.
OUTPUT_LOW(RF_24G_CE);
OUTPUT_HIGH(RF_24G_CS);
CSDELAY();
OUTPUT_LOW(RF_24G_DATA);
OUTPUT_HIGH(RF_24G_CLK1);
CLKDELAY();
OUTPUT_LOW(RF_24G_CLK1);
CLKDELAY();
OUTPUT_LOW(RF_24G_CS);
OUTPUT_LOW(RF_24G_CLK1);
}
void RF_24G_SetRxByte() {
OUTPUT_LOW(RF_24G_CE);
OUTPUT_HIGH(RF_24G_CS);
CSDELAY();
putByte(RF_CH | RXEN_RX);
OUTPUT_LOW(RF_24G_CS);
OUTPUT_FLOAT(RF_24G_DATA);
OUTPUT_LOW(RF_24G_CLK1);
OUTPUT_HIGH(RF_24G_CE);
}
void RF_24G_SetRx() {
// Once the wanted protocol, modus and RF channel are set,
// only one bit (RXEN) is shifted in to switch between RX and TX.
OUTPUT_LOW(RF_24G_CE);
OUTPUT_HIGH(RF_24G_CS);
CSDELAY();
OUTPUT_HIGH(RF_24G_DATA);
OUTPUT_HIGH(RF_24G_CLK1);
CLKDELAY();
OUTPUT_LOW(RF_24G_CLK1);
CLKDELAY();
OUTPUT_LOW(RF_24G_CS);
OUTPUT_FLOAT(RF_24G_DATA);
OUTPUT_LOW(RF_24G_CLK1);
OUTPUT_HIGH(RF_24G_CE);
}
void putBuffer() {
int8 i;
OUTPUT_HIGH(RF_24G_CE);
CSDELAY();
putByte(ADDR1_1);
putByte(ADDR1_0);
for( i=0; i<BUF_MAX ; i++) {
putByte(buf[i]);
}
OUTPUT_LOW(RF_24G_CE);
OUTPUT_LOW(RF_24G_CLK1);
}
void getBuffer() {
int8 i;
for( i=0; i<BUF_MAX ; i++) {
buf[i] = getByte();
}
OUTPUT_LOW(RF_24G_CLK1);
OUTPUT_HIGH(RF_24G_CE);
}
////////////////////////////////////////////////////////////////////////////////
//Example Setup:
//
// RF_24G_initPorts();
// RF_24G_Config();
// RF_24G_SetRx(); // Switch to receive
// buf[0] = 'A';
// buf[1] = 'B'; // Not used
// buf[2] = 'C'; // Not used
// buf[3] = 'D'; // Not used
//
// while(1) {
// if(INPUT(RF_24G_DR1)){
// getBuffer(); // Get packet
// putc(buf[0]);
// }
//
//
// // Transmit RF
// RF_24G_SetTx(); // switch to transmit
// delay_ms(1);
// putBuffer(); // send packet (buf)
// delay_ms(1); // won't go back to recieve without this
// RF_24G_SetRx(); // switch back to receive
// delay_ms(1);
// } |
-special [k] |
|
 |
specialk
Joined: 12 Nov 2005
Posts: 27
|
|
| Posted: Fri Aug 18, 2006 11:01 am |
|
|
Here's a slightly modified and updated version:
| Code: | ////////////////////////////////////////////////////////////////////////////////
// Laipac RF-24G / TXRX24G
// 2.4GHz Wireless Transceiver Driver
//
// Original by micro222@yahoo.com
//
// Filename : RF-24G_6-byte.c
// Programmer : Steven Cholewiak, www.semifluid.com
// Version : Version 1.01 - 01/30/2006
// Remarks : Datasheets for RF-24G / TXRX24G are available from:
// http://www.sparkfun.com/datasheets/RF/RF-24G_datasheet.pdf
// http://www.sparkfun.com/datasheets/RF/RF-24G.pdf
// http://www.sparkfun.com/datasheets/RF/nRF2401rev1_1.pdf
// http://store.qkits.com/moreinfo.cfm/txrx24g.pdf
//
// This code is modified from the original to support more
// configuration options with more information provided about
// each configuration byte.
//
// History : Version 1.01 - 01/30/2006
// - numOfBytes is now used to describe the packet payload and
// adjusts DATA1_W, DATA2_W, and BUF_MAX accordingly
//
// Version 1.00 - 01/21/2006
// - Initial release
////////////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////
//Pin Configuration
//
// Pin Name Pin funtion Description
// 1 GND Power Gound (0V)
// 2 CE Input Chip Enable activates RX or TX mode
// 3 CLK2 I/O Clock output/input for RX data channel 2
// 4 CS Input Chip Select activates Configuration mode
// 5 CLK1 I/O Clock Input(TX)&I/O(RX) for data channel 1 3-wire interface
// 6 DATA I/O RX data channel 1/TX data input /3-wire interface
// 7 DR1 Output RX data ready at data channel 1 (ShockBurst only)
// 8 DOUT2 Output RX data channel 2
// 9 DR2 Output RX data ready at data channel 2 (ShockBurst only)
// 10 VCC Power Power Supply (+3V DC)
#define RF_24G_CE PIN_B3
#define RF_24G_DATA PIN_B4
#define RF_24G_CLK1 PIN_B5
//#define RF_24G_CLK2 PIN_B0
#define RF_24G_DR1 PIN_B6
#define RF_24G_CS PIN_B7
//#define RF_24G_DOUT2 PIN_B4
//#define RF_24G_DR2 PIN_B7
////////////////////////////////////////////////////////////////////////////////
#define numOfBytes 6
#inline
RF_24G_initPorts() {
PORT_B_PULLUPS(FALSE);
DISABLE_INTERRUPTS(INT_RB);
}
////////////////////////////////////////////////////////////////////////////////
//Configuration Bytes
//
//Bytes 14-02: Shockburst Configuration
//Bytes 01-00: General Device Configuration
//Byte 14: Length of data payload section RX channel 2 in bits
// The total number of bits in a ShockBurst RF package may not exceed 256!
// Maximum length of payload section is hence given by:
// DATAx_W(bits) = 256 - ADDR_W - CRC
#define DATA2_W numOfBytes * 8
//Byte 13: Length of data payload section RX channel 1 in bits
#define DATA1_W numOfBytes * 8
//Byte 12-08: Channel 2 Address
#define ADDR2_4 0x00
#define ADDR2_3 0x00
#define ADDR2_2 0x00
#define ADDR2_1 0x42
#define ADDR2_0 0x42
//Byte 07-03: Channel 1 Address
#define ADDR1_4 0x00
#define ADDR1_3 0x00
#define ADDR1_2 0x00
#define ADDR1_1 0x42
#define ADDR1_0 0x42
//Byte 02
// Bit 07-02: ADDR_W - Number of address bits (both RX channels)
// Maximum number of address bits is 40 (5 bytes)
// Bit 01: CRC_L - 8 or 16 bits CRC
// Bit 00: CRC_EN - Enable on-chip CRC generation/checking
// Combine (via |) together constants from each group
// 0b76543210
#define ADDR_W_5_BYTE 0b10100000
#define ADDR_W_4_BYTE 0b10000000
#define ADDR_W_3_BYTE 0b01100000
#define ADDR_W_2_BYTE 0b01000000
#define ADDR_W_1_BYTE 0b00100000
#define CRC_L_8_BIT 0b00000000
#define CRC_L_16_BIT 0b00000010
#define CRC_EN_DISABLE 0b00000000
#define CRC_EN_ENABLE 0b00000001
//Byte 01
// Bit 07: RX2_EN - Enable two channel receive mode
// Bit 06: CM - Communication mode ( Direct or ShockBurst)
// Bit 05: RFDR_SB - RF data rate (1Mbps requires 16MHz crystal)
// Bit 04-02: XO_F - Crystal frequency (Factory default 16MHz crystal mounted)
// Bit 01-00: RF_PWR - RF output power
// Combine (via |) together constants from each group
// 0b76543210
#define RX2_EN_DISABLE 0b00000000
#define RX2_EN_ENABLE 0b10000000
#define CM_DIRECT 0b00000000
#define CM_SHOCKBURST 0b01000000
#define RFDR_SB_250_KBPS 0b00000000
#define RFDR_SB_1_MBPS 0b00100000
#define XO_F_4MHZ 0b00000000
#define XO_F_8MHZ 0b00000100
#define XO_F_12MHZ 0b00001100
#define XO_F_16MHZ 0b00001100
#define XO_F_20MHZ 0b00010000
#define RF_PWR_N20DB 0b00000000 // -20db
#define RF_PWR_N10DB 0b00000001 // -10db
#define RF_PWR_N5DB 0b00000010 // -5db
#define RF_PWR_0DB 0b00000011 // 0db (Full Power)
//Byte 01
// Bit 07-01: RF_CH# - Frequency channel (2400MHz + RF_CH# * 1.0MHz)
// Bit 00: RXEN - RX or TX operation
// Combine (via |) together constants from each group
// 0b76543210
#define RF_CH 0b10000000 // 64 - 2464GHz
#define RXEN_TX 0b00000000
#define RXEN_RX 0b00000001
////////////////////////////////////////////////////////////////////////////////
#define BUF_MAX numOfBytes
byte buf[BUF_MAX];
#define CLKDELAY() delay_us(1)
#define CSDELAY() delay_us(10)
#define PWUPDELAY() delay_ms(3)
void putByte( byte b ) { //MSB bit first
int8 i;
int8 p = 7;
for(i=0 ; i < 8 ; i++) {
OUTPUT_LOW(RF_24G_CLK1);
if( BIT_TEST(b,p--) ) {
OUTPUT_HIGH(RF_24G_DATA);
}else{
OUTPUT_LOW(RF_24G_DATA);
}
CLKDELAY();
OUTPUT_HIGH(RF_24G_CLK1); // Clock out on rising edge
CLKDELAY();
}
}
byte getByte() { //MSB bit first
int8 i , b = 0;
int8 p = 7;
for(i=0 ; i < 8 ; i++) {
OUTPUT_LOW(RF_24G_CLK1);
CLKDELAY();
OUTPUT_HIGH(RF_24G_CLK1);
CLKDELAY(); // Read before falling edge
if( INPUT(RF_24G_DATA) ) {
BIT_SET(b,p--);
}else{
BIT_CLEAR(b,p--);
}
}
return b;
}
void RF_24G_Config() {
OUTPUT_LOW(RF_24G_CE);
OUTPUT_LOW(RF_24G_CS);
OUTPUT_LOW(RF_24G_CLK1);
OUTPUT_LOW(RF_24G_DATA);
PWUPDELAY();
OUTPUT_HIGH(RF_24G_CS);
CSDELAY();
//MSB byte first
putByte(DATA2_W);
putByte(DATA1_W);
putByte(ADDR2_4);
putByte(ADDR2_3);
putByte(ADDR2_2);
putByte(ADDR2_1);
putByte(ADDR2_0);
putByte(ADDR1_4);
putByte(ADDR1_3);
putByte(ADDR1_2);
putByte(ADDR1_1);
putByte(ADDR1_0);
putByte(ADDR_W_2_BYTE | CRC_L_16_BIT | CRC_EN_ENABLE);
putByte(RX2_EN_DISABLE | CM_SHOCKBURST | RFDR_SB_1_MBPS | XO_F_16MHZ | RF_PWR_0DB);
putByte(RF_CH | RXEN_RX);
OUTPUT_FLOAT(RF_24G_DATA);
OUTPUT_LOW(RF_24G_CE);
OUTPUT_LOW(RF_24G_CS);
OUTPUT_LOW(RF_24G_CLK1);
}
void RF_24G_SetTxByte() {
OUTPUT_LOW(RF_24G_CE);
OUTPUT_HIGH(RF_24G_CS);
CSDELAY();
putByte(RF_CH | RXEN_TX);
OUTPUT_LOW(RF_24G_CS);
OUTPUT_LOW(RF_24G_CLK1);
}
void RF_24G_SetTx() {
// Once the wanted protocol, modus and RF channel are set,
// only one bit (RXEN) is shifted in to switch between RX and TX.
OUTPUT_LOW(RF_24G_CE);
OUTPUT_HIGH(RF_24G_CS);
CSDELAY();
OUTPUT_LOW(RF_24G_DATA);
OUTPUT_HIGH(RF_24G_CLK1);
CLKDELAY();
OUTPUT_LOW(RF_24G_CLK1);
CLKDELAY();
OUTPUT_LOW(RF_24G_CS);
OUTPUT_LOW(RF_24G_CLK1);
}
void RF_24G_SetRxByte() {
OUTPUT_LOW(RF_24G_CE);
OUTPUT_HIGH(RF_24G_CS);
CSDELAY();
putByte(RF_CH | RXEN_RX);
OUTPUT_LOW(RF_24G_CS);
OUTPUT_FLOAT(RF_24G_DATA);
OUTPUT_LOW(RF_24G_CLK1);
OUTPUT_HIGH(RF_24G_CE);
}
void RF_24G_SetRx() {
// Once the wanted protocol, modus and RF channel are set,
// only one bit (RXEN) is shifted in to switch between RX and TX.
OUTPUT_LOW(RF_24G_CE);
OUTPUT_HIGH(RF_24G_CS);
CSDELAY();
OUTPUT_HIGH(RF_24G_DATA);
OUTPUT_HIGH(RF_24G_CLK1);
CLKDELAY();
OUTPUT_LOW(RF_24G_CLK1);
CLKDELAY();
OUTPUT_LOW(RF_24G_CS);
OUTPUT_FLOAT(RF_24G_DATA);
OUTPUT_LOW(RF_24G_CLK1);
OUTPUT_HIGH(RF_24G_CE);
}
void putBuffer() {
int8 i;
OUTPUT_HIGH(RF_24G_CE);
CSDELAY();
putByte(ADDR1_1);
putByte(ADDR1_0);
for( i=0; i<BUF_MAX ; i++) {
putByte(buf[i]);
}
OUTPUT_LOW(RF_24G_CE);
OUTPUT_LOW(RF_24G_CLK1);
}
void getBuffer() {
int8 i;
for( i=0; i<BUF_MAX ; i++) {
buf[i] = getByte();
}
OUTPUT_LOW(RF_24G_CLK1);
OUTPUT_HIGH(RF_24G_CE);
}
////////////////////////////////////////////////////////////////////////////////
//Example Setup:
//
// RF_24G_initPorts();
// RF_24G_Config();
// RF_24G_SetRx(); // Switch to receive
// buf[0] = 'A';
// buf[1] = 'B'; // Not used
// buf[2] = 'C'; // Not used
// buf[3] = 'D'; // Not used
//
// while(1) {
// if(INPUT(RF_24G_DR1)){
// getBuffer(); // Get packet
// putc(buf[0]);
// }
//
//
// // Transmit RF
// RF_24G_SetTx(); // switch to transmit
// delay_ms(1);
// putBuffer(); // send packet (buf)
// delay_ms(1); // won't go back to recieve without this
// RF_24G_SetRx(); // switch back to receive
// delay_ms(1);
// }
|
|
|
|
future
Joined: 14 May 2004
Posts: 330
|
|
| Posted: Sat Sep 19, 2009 1:25 pm |
|
|
Hi specialk,
How far can you stream data with this transceiver? |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ 
Search
Register
Profile 
Log in to check your private messages 
Log in
