CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support
PIC18F8680 / external memory

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
pasini



Joined: 12 Dec 2005
Posts: 50
Location: Curitiba - Brazil

View user's profile Send private message Send e-mail

PIC18F8680 / external memory
PostPosted: Thu Mar 16, 2006 6:10 am     Reply with quote
Hi all,

Does anyone know if PIC18F8680 controls pin J5 (CE = chip enable) while accessing external memory or I have to control it ?

CCS3.241 MPLAB 7.31

I´ve done everything to make the interface work but the flash memory does not responde properly.

CE tries to be high but just a spurious pulse appears.

A piece of my code is as follows.

Thanks in advance
Pasini




Code:

#include "18f8680.h"
#device *=16 ADC=10
#fuses HS,NOWDT,NOPUT,NOPROTECT,BROWNOUT,NOLVP,NOCPD,NOWRT,EMCU,NOWAIT
#use delay(clock=20000000)
#case

#define BASE 0x010000


int16 add;
int16 val;

void main(void)
{
                int16 c=0;
   
   setup_ccp1 (CCP_OFF); // disable PWM hardware
   setup_ccp2 (CCP_OFF); // disable PWM hardware

   setup_adc_ports(AN0_TO_AN1|VSS_VDD);
   setup_adc(ADC_CLOCK_DIV_32);

    setup_timer_0(RTCC_INTERNAL|RTCC_DIV_4);
    setup_timer_2(T2_DIV_BY_16,150,3);

    setup_external_memory(EXTMEM_DISABLE|EXTMEM_WORD_WRITE|EXTMEM_WAIT_0);

   
   set_tris_a(0b00010011);
   set_tris_g(0b00000101);
   set_tris_c(0b11000011);
   set_tris_f(0b00000000);
   set_tris_j(0b00000000);

   output_high(PIN_A3);

// chip erase
   write_external_memory(0x0555,0x00AA,2);
   delay_ms(300);
   write_external_memory(0x02AA,0x0055,2);
   delay_ms(300);
   write_external_memory(0x0555,0x0080,2);
   delay_ms(300);   
   write_external_memory(0x0555,0x00AA,2);
   delay_ms(300);
   write_external_memory(0x02AA,0x0055,2);
   delay_ms(300);
   write_external_memory(0x0555,0x0010,2);
   delay_ms(300);

   delay_ms(500);

   read_external_memory(add+BASE, &val, 2); 

   add = 0;   

   while(1)
   {   val = 0;
      write_external_memory(0x0555,0x00AA,2);
      write_external_memory(0x02AA,0x0055,2);
      write_external_memory(0x0555,0x00A0,2);
      write_external_memory(add+BASE, &val, 2);
      add++;

   }
   
}
Ttelmah
Guest
PostPosted: Thu Mar 16, 2006 4:14 pm     Reply with quote
I think you are talking to the wrong addresses...
The address value, is a 32bit number, not a 16bit value. If you were running with the external memory starting at address 0 (in microprocessor mode), then it would begin at this point. However in extended microcontroller mode, the address range for the external memory, begins at 0x0c000.
You also probably don't want the memory disabled (though the code should override this), unless you are using the pins for other functions.
So try:
setup_external_memory (EXTMEM_WORD_WRITE|EXTMEM_WAIT_0);

and

write_external_memory(0x0C555,0x00AA,2);

Best Wishes
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group