CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support
PIC16f526 PIN C5 output

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
aldina



Joined: 09 Oct 2009
Posts: 26

View user's profile Send private message Send e-mail

PIC16f526 PIN C5 output
PostPosted: Wed Sep 15, 2021 2:12 am     Reply with quote
Hello all,

I can't use PIN C5 of PIC16f526 as output. I've fixed this pin as output port but when I use OUTPUT_HIGH(PIN_C5) nothing happen.
Code:

##include <16F526.h>
#device ADC=8
#fuses INTRC,WDT,MCLR,PROTECT
#use delay(clock=8000000)
#use fixed_io (c_outputs = pin_c5)
#use fixed_io (b_outputs = pin_b5)

void main()
{
   int8 RH_Signal, LH_Signal;
   
   setup_comparator(NC_NC_NC_NC);
   
   setup_adc_ports(PIN_B0);
   setup_adc_ports(PIN_B1);
   setup_adc(ADC_CLOCK_DIV_16);
   
   output_low(PIN_B5); //sector Lateral Direito
   output_low(PIN_C5); //sector Lateral Esquerdo
   
   while (true)
   {
      restart_wdt();
     
      RH_Signal = 0;
      LH_Signal = 0;
     
      RH_Signal = Right();
      LH_Signal = Left();
     
      if(RH_Signal >= 50 && LH_Signal >= 50)
      {
         if(input(PIN_B2) == 1 || input(PIN_C0) == 1)
         {
            OUTPUT_HIGH(PIN_B5); // ON - Right Light output
            OUTPUT_HIGH(PIN_C5); // ON - Left Light output
            T_OFF4();
         }
         else if(input(PIN_B2) == 0 && input(PIN_C0) == 0)
         {
            OUTPUT_HIGH(PIN_B5); // ON - Right Light output
            OUTPUT_HIGH(PIN_C5); // ON - Left Light output
            T_OFF4();
         }
      }
   }
}

Can someone help me? Why Pin C5 doesn't come HIGH state?
Thanks,
Ttelmah



Joined: 11 Mar 2010
Posts: 19510

View user's profile Send private message

PostPosted: Wed Sep 15, 2021 2:32 am     Reply with quote
Key here is the data sheet.
If you look at C5, and table 6-3, you will see that the priority on this pin has
the timer0 input taking priority over the standard I/O functions. You need to
turn this off. Setting Timer0, to use the internal clock should disable this
input selection.

setup_timer_0(T0_INTERNAL);

If you look at Register 4-2, you will see that the default on power on, is
to set the T0CS bit to '1', which has the Timer0 input selected.
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group