 |
 |
| View previous topic :: View next topic |
| Author |
Message |
Eddy71ua
Joined: 23 Sep 2009
Posts: 55
Location: Ukraine
|
| [Solved] ADC PIC16F1823 ..half-work |
 Posted: Wed Jul 18, 2018 8:33 am |
 |
|
An incomprehensible problem arose: the reading of the channel AN3 gives only zero continuously. AN6 reads normally.
It seems to me that the channel does not turn on
| Code: |
#include <16F1823.h>
#device adc=10
#fuses INTRC_IO,NOWDT,NOPUT,PROTECT,NOIESO,NOFCMEN,WRT,NOSTVREN,NOLVP,NOMCLR,NODEBUG,BORV25
#use delay(clock=8000000)
#use fast_io(a)
#use fast_io(c)
#zero_ram
#use rs232(baud=9600,parity=N,xmit=PIN_C3,bits=8)
//----------------------------------------------//
void main(){
int16 Tmp16;
setup_oscillator(OSC_8MHZ);
setup_wdt(WDT_OFF);
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_4);
setup_timer_1(T1_DISABLED);
setup_timer_2(T2_DISABLED,0,1);
setup_comparator(NC_NC_NC_NC);
set_tris_a(0b011110);
set_tris_c(0b000100);
port_a_pullups(0b110);
port_c_pullups(false);
setup_adc_ports(sAN3|sAN6|VSS_VDD);
setup_adc(ADC_CLOCK_DIV_8);
setup_vref(VREF_ON|VREF_ADC_1v024);
setup_adc_reference(VSS_VDD);
for(;;){
set_adc_channel(sAN3);
delay_us(200);
Tmp16 = read_adc();
printf("nA = %lu \r",Tmp16);
set_adc_channel(sAN6);
delay_us(200);
Tmp16 = read_adc();
printf("nB = %lu \r",Tmp16);
delay_ms(1000);
}
}
|
----------------
PCWHD v5.078
Last edited by Eddy71ua on Wed Jul 18, 2018 11:27 am; edited 1 time in total |
|
 |
PCM programmer
Joined: 06 Sep 2003
Posts: 21708
|
| Re: ADC PIC16F1823 ..half-work |
| Posted: Wed Jul 18, 2018 9:05 am |
|
|
| Eddy71ua wrote: |
set_adc_channel(sAN3);
delay_us(200);
Tmp16 = read_adc();
printf("nA = %lu \r",Tmp16);
set_adc_channel(sAN6);
|
That's not the correct way to set the A/D channel.
You must use the actual channel number, such as 3 or 6, as the parameter. |
|
|
Ttelmah
Joined: 11 Mar 2010
Posts: 19518
|
|
| Posted: Wed Jul 18, 2018 10:18 am |
|
|
a couple of other comments:
setup_wdt(WDT_OFF);
This is a wasted instruction. You have the WDT turned off in the fuses. When it is turned off this way, the setup_wdt instruction cannot control it....
Then you have:
setup_vref(VREF_ON|VREF_ADC_1v024);
Why?. You are using Vss to Vdd as your reference, so all this does is turn the Vref on, and waste power.
As a note, this is actually not a usable setting. The minimum Vref for the ADC is 2.048. From the data sheet:
| Quote: |
ADC Reference Voltage (REF+) is the selected input, VREF+ pin, VDD pin or the FVR Buffer 1. When the FVR is selected
as the reference input, the FVR Buffer 1 output selection must be 2.048V or 4.096V (ADFVR<1:0> = 1x).
|
The 1.048 setting is only really there for use with other peripherals. |
|
|
Eddy71ua
Joined: 23 Sep 2009
Posts: 55
Location: Ukraine
|
| Re: ADC PIC16F1823 ..half-work |
| Posted: Wed Jul 18, 2018 11:26 am |
|
|
| PCM programmer wrote: |
That's not the correct way to set the A/D channel.
You must use the actual channel number, such as 3 or 6, as the parameter. |
Oops .. You're right, I was wrong.
| Quote: | Then you have:
setup_vref(VREF_ON|VREF_ADC_1v024);
Why?. |
Next, I measure the battery power.
 |
|
|
Ttelmah
Joined: 11 Mar 2010
Posts: 19518
|
|
| Posted: Wed Jul 18, 2018 12:13 pm |
|
|
| You still can't use the 1.024 volt setting. The _minimum_ voltage allowed for the voltage reference on the ADC is 1.8v. As I said the 1.024v setting is for other peripherals that can use the Vref source. |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ 
Search
Register
Profile 
Log in to check your private messages 
Log in
