CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support
Hardware Uart in 9 bit mode [Solved]

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
kmp84



Joined: 02 Feb 2010
Posts: 345

View user's profile Send private message

Hardware Uart in 9 bit mode [Solved]
PostPosted: Thu Jul 27, 2017 2:29 pm     Reply with quote
Hello All,

I want to ask you if this is the right way to use hardware uart in 9 bit addressing mode.

Example:

Code:

#use rs232(baud=9600,rcv=PIN_C7,xmit=PIN_C6,bits=9,ERRORS,stream=B485)

#bit ninth_bit = RS232_ERRORS.7

byte TestPacket[] = {0x07, 0x01, 0x01, 0x00, 0x08, 0x1A, 0x00, 0x2B};


void SendDataToB(int8 *data, int8 len){
   int8 i;     
   
   for(i = 0; i < len; i++){
      if(i == 0)
         ninth_bit=1;
      else
         ninth_bit=0;
     
      fputc(data[i], B485);  // Send data
   }
}


I'm sending an example "TestPacket" but the device is not responding.
What could be the problem?

Thanks for attention!

Last edited by kmp84 on Thu Jul 27, 2017 3:01 pm; edited 1 time in total
Ttelmah



Joined: 11 Mar 2010
Posts: 19504

View user's profile Send private message

PostPosted: Thu Jul 27, 2017 2:34 pm     Reply with quote
You don't have to.

Assuming a reasonably modern compiler, when set to 9bit mode, the getc, and putc instructions will accept a 16bit value, and handle the extra bit automatically (the functions are 'overloaded', and if they see a 16bit value, switch operation to handle this).
temtronic



Joined: 01 Jul 2010
Posts: 9225
Location: Greensville,Ontario

View user's profile Send private message

PostPosted: Thu Jul 27, 2017 2:44 pm     Reply with quote
I have a question...

You have 'stream=B485' in the USE RS232(...options...)

To me, that implies you're using an RS485 transceiver. If so, you also need to declare the 'control' pin for the TXX/RXD of the RS485 device. Unless it being used ONLY for one direction of data.

Also, if RS485 is being used, you need to use the correct pullup/pull down and termination resistors. These will be detailed in the RS485 device datasheet.

Jay
kmp84



Joined: 02 Feb 2010
Posts: 345

View user's profile Send private message

PostPosted: Thu Jul 27, 2017 2:46 pm     Reply with quote
Hi Mr.Ttelmah,

How to handle 9 bit? Some example please?

Thanks,
kmp84



Joined: 02 Feb 2010
Posts: 345

View user's profile Send private message

PostPosted: Thu Jul 27, 2017 2:55 pm     Reply with quote
temtronic wrote:
I have a question...

You have 'stream=B485' in the USE RS232(...options...)

To me , that implies you're using an RS485 transceiver. If so, you also need to declare the 'control' pin for the TXX/RXD of the RS485 device. Unless it being used ONLY for one direction of data.

Also, if RS485 is being used, you need to use the correct pullup/pull down and termination resistors. These will be detailed in teh RS485 device datasheet.

Jay


At the moment I'm using rs232 , but hardware also has and rs485 with this settings :

Code:

#use rs232(baud=9600,rcv=PIN_C7,xmit=PIN_C6,enable=pin_B2,bits=9,ERRORS,stream=B485)
temtronic



Joined: 01 Jul 2010
Posts: 9225
Location: Greensville,Ontario

View user's profile Send private message

PostPosted: Thu Jul 27, 2017 5:22 pm     Reply with quote
OK... what does the device use for communications? RS232 or RS485 ?? There is a BIG difference in the hardware AND then there's the software side to consider.
You cannot just connect a PIC up directly to the 'device', you need the correct interface chip(s).
If the 'device' is a commercial product, provide a link to the datasheet. That will help us.

'Not working' could be you've got a bare PIC tied to the device, you have TXD and RXD swapped, missing ground between devices, MAX232 tied to MAX485, and that's just a start of possibles....

Happy to help but I need more details about the project.

Jay
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Thu Jul 27, 2017 7:37 pm     Reply with quote
Quote:
I want to ask you if this is the right way to use hardware uart in 9 bit addressing mode.

CCS gives examples of how to do this in the RS485.c file, in the drivers folder.

UART setup:
Code:
  #use rs232(baud=9600, xmit=RS485_TX_PIN, rcv=RS485_RX_PIN, enable=RS485_ENABLE_PIN, bits=9, long_data, errors, stream=RS485)


Look at this function in the RS485.c file:
Code:
int1 rs485_send_message(unsigned int8 to, unsigned int8 len, unsigned int8* data) {
.
.
.
}
kmp84



Joined: 02 Feb 2010
Posts: 345

View user's profile Send private message

Problem Solved
PostPosted: Tue Aug 15, 2017 4:13 pm     Reply with quote
Hello All,

Sorry for my delayed response. I did not have for a long time PC and internet connection.
I have made successful communication in "9 bit long_data" format with hardware uart and also with software uart over physical rs232 and rs485.

Thank you very much !
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group