![](templates/subSilver/images/CCSLogo.jpg) |
![CCS C Software and Maintenance Offers](templates/subSilver/images/forumAd6.jpg) |
View previous topic :: View next topic |
Author |
Message |
aaronik19
Joined: 25 Apr 2011 Posts: 297
|
MCP23008 reading port |
Posted: Sat May 11, 2013 6:07 pm |
|
|
hello friends,
I have the following code:
Code: | MCP23008_write(MCP23008_3_write, _IODIR, 0xFF); // All Pins are Inputs
MCP23008_write(MCP23008_3_write, _IPOL, 0x00); // All Outputs are similar to inputs
MCP23008_write(MCP23008_3_write, _GPINTEN, 0xFF); //All Interrupt on Change
MCP23008_write(MCP23008_3_write, _DEFVAL, 0x00); //To Compare GPINTEN & INTCON against DEFVAL
MCP23008_write(MCP23008_3_write, _INTCON 0xFF); //Compare with 0 value
MCP23008_write(MCP23008_3_write, _IOCON, 0x02); //int active high
MCP23008_write(MCP23008_3_write, _GPPU, 0x00); // Disable Pull-Up Resistors
MCP23008_write(MCP23008_3_write, _INTF, 0x00);
MCP23008_write(MCP23008_3_write, _GPIO, 0x00);
MCP23008_write(MCP23008_3_write, _OLAT, 0x00); |
the problem is that the setup is good but the interrupt is not being fired. I am sending this code to setup the MCP23008 as input (read) on Interrupt change. I read all the datasheet and related application note but still in the same problem. Can someone please guide me if I've setup the MCP23008 correctly?
Thanks |
|
![](templates/subSilver/images/spacer.gif) |
asmboy
Joined: 20 Nov 2007 Posts: 2128 Location: albany ny
|
|
Posted: Sun May 12, 2013 11:36 am |
|
|
without source code for
MCP23008_write()
and how you use it in MAIN()
how can anybody tell what
is going on ?? |
|
![](templates/subSilver/images/spacer.gif) |
aaronik19
Joined: 25 Apr 2011 Posts: 297
|
|
Posted: Sat Mar 01, 2014 10:26 pm |
|
|
dear all,
I continue to work on this chip and still have problems to clear interrupt when read the INTCON register. This is the driver code:
Code: | FUNCTIONS DEFINITIONS
#define MCP23008_1_write 0x4E
#define MCP23008_1_read 0x4F
#define MCP23008_2_write 0x48
#define MCP23008_2_read 0x49
#define MCP23008_3_write 0x4C
#define MCP23008_3_read 0x4D
// MCP23008 REGISTERS
#define _IODIR 0x00 // determines if the pin is input or output
#define _IPOL 0x01 // the polarity of the input. Can have invert input
#define _GPINTEN 0x02 // interrupt on change input
#define _DEFVAL 0x03 // default comparision
#define _INTCON 0x04 // compare with the DEFVAL during interrupt
#define _IOCON 0x05 // I/O Expander configuration
#define _GPPU 0x06 // pull-up resistors
#define _INTF 0x07 // interrupt flag
#define _INTCAP 0x08 // capture the state of the port during interrupt
#define _GPIO 0x09 // actual input/outputs on the port
#define _OLAT 0x0A // logic level register of the output port
long int MCP23008_read(unsigned int WriteAddress, unsigned int cmdByte, unsigned int ReadAddress)
{
unsigned int data;
i2c_start(); // start condition
delay_us(20);
i2c_write(WriteAddress); // Send slave address and clear (R/W_)
delay_us(20);
i2c_write(cmdByte); // Command byte and register to be written.
delay_us(50);
i2c_start();
delay_us(20); // restart condition
i2c_write(ReadAddress); // Send slave address and clear (R_/W)
delay_us(20);
data = i2c_read(); // Data from LSB or MSB of register
delay_us(20);
i2c_stop(); // stop condition
return(data);
}
void MCP23008_write(unsigned char location, unsigned char addr, unsigned char data)
{
i2c_start();
delay_us(20);
i2c_write(location);
delay_us(20);
i2c_write(addr);
delay_us(20);
i2c_write(data);
delay_us(20);
i2c_stop();
delay_us(20);
}
void MCP23008_init()
{
output_float(PIN_C4);
output_float(PIN_C3); //signals to prepare MCP for operation
delay_ms(250); //delay for MCP23008 start-up
MCP23008_write(MCP23008_1_write, _IODIR, 0x00); // All Pins are Outputs
MCP23008_write(MCP23008_1_write, _IPOL, 0x00); // All Outputs are similar to inputs
MCP23008_write(MCP23008_1_write, _IOCON, 0x00);
MCP23008_write(MCP23008_2_write, _IODIR, 0x00); // All Pins are Outputs
MCP23008_write(MCP23008_2_write, _IPOL, 0x00); // All Outputs are similar to inputs
MCP23008_write(MCP23008_2_write, _IOCON, 0x00);
MCP23008_write(MCP23008_3_write, _IODIR, 0xFF); // All Pins are Inputs
MCP23008_write(MCP23008_3_write, _IPOL, 0x00); // All Outputs are similar to inputs
MCP23008_write(MCP23008_3_write, _GPINTEN, 0xFF); //All Interrupt on Change
MCP23008_write(MCP23008_3_write, _DEFVAL, 0x00); //To Compare GPINTEN & INTCON against DEFVAL
MCP23008_write(MCP23008_3_write, _INTCON 0xFF); //Compare with Defcal Register
MCP23008_write(MCP23008_3_write, _IOCON, 0x0A);
MCP23008_write(MCP23008_3_write, _GPPU, 0x00); // Disable Pull-Up Resistors
MCP23008_write(MCP23008_3_write, _IOCON, 0x00);
MCP23008_write(MCP23008_3_write, _GPIO, 0x00);
MCP23008_write(MCP23008_3_write, _OLAT, 0x00);
} |
the main code is:
Code: | #include <program.h>
#include <mcp23008.c>
//VARIABLES FOR THE PROGRAM
int counter1 = 0;
int GP_count = 0;
int8 read_port = 0;
#INT_EXT
void EXT_isr(void)
{
output_high(PIN_D1);
output_high(PIN_D2);
read_port = MCP23008_Read(0x4C,0x08, 0x4D);
output_low(PIN_D1);
mcp23008_write(0x48, 0x09, read_port);
output_low(PIN_D2);
}
void main()
{
mcp23008_init();
enable_interrupts(INT_EXT);
ext_int_edge( H_TO_L );
enable_interrupts(GLOBAL);
while(TRUE)
{
}
} |
I also draw the circuit on proteus but this is real simulation and not software simulation. Used proteus only to show the circuit
http://postimg.org/image/47llzictt/ |
|
![](templates/subSilver/images/spacer.gif) |
PCM programmer
Joined: 06 Sep 2003 Posts: 21708
|
|
Posted: Sat Mar 01, 2014 10:38 pm |
|
|
Quote: |
data = i2c_read(); // Data from LSB or MSB of register |
This is the same old problem. It's missing the NAK on the last i2c_read
in your MCP23008_read() function.
In your thread here, from 2011, you had the NAK in there. Why did
you take it out in your latest code ? It's essential:
http://www.ccsinfo.com/forum/viewtopic.php?t=46502
In this thread here, which looks like the place you got the driver from,
he makes the missing NAK mistake and I correct it:
http://www.ccsinfo.com/forum/viewtopic.php?t=22639 |
|
![](templates/subSilver/images/spacer.gif) |
aaronik19
Joined: 25 Apr 2011 Posts: 297
|
|
Posted: Sun Mar 02, 2014 12:09 am |
|
|
thanks I solve that problem. I forgot the "0"...thanks
But the problem is that When I press the button, the interrupt is working and it is being written on the second MCP chip. The problem is that when I press another button nothing is happening. ON the datasheet it is mentioned that when the register INTCON (0x08) is being read, the interrupt will be reset. Do I missing something please? |
|
![](templates/subSilver/images/spacer.gif) |
aaronik19
Joined: 25 Apr 2011 Posts: 297
|
|
Posted: Sun Mar 02, 2014 9:29 am |
|
|
Afterr more time trying, i am still have no success....any help please? |
|
![](templates/subSilver/images/spacer.gif) |
Mike Walne
Joined: 19 Feb 2004 Posts: 1785 Location: Boston Spa UK
|
|
Posted: Sun Mar 02, 2014 2:16 pm |
|
|
Reduce your code to a few lines so showing us what your real problem is.
Mike |
|
![](templates/subSilver/images/spacer.gif) |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|