CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com
Mouse Driver for ex_usb_mouse.c

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
linera



Joined: 23 Nov 2011
Posts: 6

View user's profile Send private message

Mouse Driver for ex_usb_mouse.c
PostPosted: Tue Apr 02, 2013 4:50 am     Reply with quote
I am trying to simulate the ex_usb_mouse.c example using proteus.
The schematic that i am using is the "picdem fs usb.dsn" sample design available in PROTEUS USB examples.
For use this schematic I have done several changes to the ex_usb_common.h file.
Code:

I defined a new profile #define USB_HW_MCHP_PIC18F4550 

#if defined(USB_HW_CCS_PIC18F4550)
   #include <18F4550.h>
   #fuses HSPLL,NOWDT,NOPROTECT,NOLVP,NODEBUG,USBDIV,PLL5,CPUDIV1,VREGEN
   #use delay(clock=48000000)
   
   //leds ordered from bottom to top
   #DEFINE LED1 PIN_A5  //green
   #define LED2 PIN_B4  //yellow
   #define LED3 PIN_B5  //red
   #define BUTTON_PRESSED() !input(PIN_A4)

   //see section below labeled USB_CABLE_IS_ATTACHED
   #define PIN_USB_SENSE   PIN_B2

   #define HW_ADC_CONFIG   ADC_CLOCK_INTERNAL
   #define HW_ADC_CHANNEL  0
   #define HW_ADC_PORTS    AN0
#endif

After several tries, I have discovered that I must change the Processor clock frequency to 2 MHz.
With this clock frequency, the messges in the RS-232 windows can be watched OK.

When I start the PROTEUS simulation, a virtual connection of the USB device to the PC is executed. The computer detects a new device connected in another device "unknown device", but i do not know which driver (.inf file) must i use to connect this device to my PC.

Someone can tell me where can i obtain the driver?

Thanks
temtronic



Joined: 01 Jul 2010
Posts: 9161
Location: Greensville,Ontario

View user's profile Send private message

PostPosted: Tue Apr 02, 2013 5:38 am     Reply with quote
Please read PIC101 thread.

If you need a proteus driver, go to proteus.

This is NOT a forum for 'simulation', rather 'stimulation'!

Most here work in the real world, coding real PICs, doing real tasks!

Even the collective brains here haven't the time or energy to deug and repair proteus.It has far too many bugs,errors,faulty DRCs.

When you get a real PIC, cut some code , most here will eagerly help you


hth
jay
linera



Joined: 23 Nov 2011
Posts: 6

View user's profile Send private message

PostPosted: Tue Apr 02, 2013 9:33 am     Reply with quote
Sorry, I have not read PIC101 thread.

I have not yet any real PIC to test it in the real world. This is the reason because I am trying to use PROTEUS in order to gain some advance.

I have installed the VIrtual USB drivers provided by proteus, but it does not work.

Moreover, I wrote a similar problem in Labcenter forums, but nobody answered yet. This is the reason because I put this new topic here.

The next time, I hope to put the new topic in the right forum.

Apologize me.
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group