CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com
software pwm

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
tmsenthil03



Joined: 27 Feb 2011
Posts: 4
Location: chennai

View user's profile Send private message

software pwm
PostPosted: Wed Jun 01, 2011 8:52 am     Reply with quote
http://www.ccsinfo.com/forum/viewtopic.php?t=30139

My question is.........

As brood discussed above . I had test this code, it is working fine. only thing is if any one in the following variable is equal to zero. the output is goes to maximum width.

red_duty = __;
green_duty = __;
blue_duty = __;

I need if these variables are equal to zero, the output will go to zero. How can i make it to Zero , pls give the note.
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Thu Jun 02, 2011 2:35 pm     Reply with quote
I modified his code a little bit and it works better now. Here is the revised program:

Code:

#include <18F4520.h>
#fuses HS,NOWDT,PUT,BROWNOUT,NOLVP
#use delay(clock=20M)

#define PRELOAD (65536 - 180)

#define RED    PIN_D0
#define GREEN  PIN_D1
#define BLUE   PIN_D2

int red_duty;
int green_duty;
int blue_duty;
int Intcount;


#int_timer1
void timer1_isr()
{
set_timer1(PRELOAD + get_timer1()); 

// Interrupt marker for viewing on oscilloscope.
//output_high(PIN_D7); 
//delay_us(1);
//output_low(PIN_D7);
   
if(Intcount == 255)
  {
   Intcount = 0;
   if(red_duty) output_high(RED);
   if(green_duty) output_high(GREEN);
   if(blue_duty) output_high(BLUE);   
  }   
   
if(Intcount == red_duty)
  {
   output_low(RED);
  }   

if(Intcount == green_duty)
  {
   output_low(GREEN);
  }   
 
if(Intcount == blue_duty)
  {
   output_low(BLUE);
  }   

Intcount++;
}


//=========================================
void main()
{

// Initialize interrupt counter and output pins.
Intcount = 0;
output_low(RED);
output_low(GREEN);
output_low(BLUE);

red_duty = 0;
green_duty = 1;
blue_duty = 2;

//red_duty = 253;
//green_duty = 254;
//blue_duty = 255;

setup_timer_1(T1_INTERNAL | T1_DIV_BY_1);
enable_interrupts(INT_TIMER1);
enable_interrupts(GLOBAL);


while(1);
}


 
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group