CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support

Zigbee damaging problem

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
hayee



Joined: 05 Sep 2007
Posts: 252

View user's profile Send private message

Zigbee damaging problem
PostPosted: Mon Jan 03, 2011 1:08 am     Reply with quote

Hi,
I am using Zigbee's from CCS. I brought many Zigbee's transceivers time to time from CCS and I am stuck in a great problem that my Zigbee's are damaging one by one.
I checked the hardware connections lot of time but the connections are right.

I have a system in which there is one coordinator and two sleepy sensors.
When I TURN ON the system, the whole system works well for certain time (time is in hours or in days) but suddenly one Zigbee stop responding (it may be a sensor Zigbee or coordinator Zigbee).

For checking that the damaged Zigbee is working or not I connect that Zigbee in another system but no response.

Can the software create a problem?
I have no idea what to do, can you guys tell me some suggestions how to solve the problem?
temtronic



Joined: 01 Jul 2010
Posts: 9226
Location: Greensville,Ontario

View user's profile Send private message

PostPosted: Mon Jan 03, 2011 6:40 am     Reply with quote

Never, ever seen code destroy a computer.It's just 1s and 0s !

More likely a hardware fault.Overvoltage to PICs, high ripple content,bad or missing grounds,induced HF or ringing. Without specifics of the actual schematic,components used and layout it's hard to say.

Are the Zigbee's 3 volt and the PIC 5 volts?
What transducers are hooked up to the remote sensors?
Any RF in the area(cell phones,CBs,Hams,etc.?
Are the units just laying round open or in aluminum case with proper grounding?
Do they 'die' randomly or say only between 3 and 4 AM?( if you think that's silly to ask, I had 30 remotes 'actup' at that time.Turned out to be crosstalk in the main telephone trunk between two cities.(Bank was updating data during that time period).Changing spanpairs cured the problem.

Can you test the system with just batteries?

The fact they work for awhile then 'die' could point the way to the source of the problem.

Obviously contact CCS to see if others have a similar problem,check for FAQ,etc.

When you find out what it is, post the solution for others.
hayee



Joined: 05 Sep 2007
Posts: 252

View user's profile Send private message

PostPosted: Mon Jan 03, 2011 7:01 am     Reply with quote

Thanks for the reply

> Are the Zigbee's 3 volt and the PIC 5 volts?
Zigbee's and PIC both are operating on 3.3v

>Any RF in the area(cell phones,CBs,Hams,etc.?
I am testing the system in a room, there are mobile phones in the room (but i personally think that this would be not the problem, if it is the problem then it would be dangerous when i implement the system in the field)

> Are the units just laying round open or in aluminum case with proper grounding?
units are just laying round open.

> Do they 'die' randomly or say only between 3 and 4 AM?( if you think that's silly to ask, I had 30 remotes 'actup' at that time.Turned out to be crosstalk in the main telephone trunk between two cities.(Bank was updating data during that time period).Changing spanpairs cured the problem.
They die randomly.

> Can you test the system with just batteries?
I can test the system with batteries but i will test it when i find the proper cause for damage otherwise i will lose another zigbee module.


Some more suggestion so that i look into the system for that.
SherpaDoug



Joined: 07 Sep 2003
Posts: 1640
Location: Cape Cod Mass USA

View user's profile Send private message

PostPosted: Mon Jan 03, 2011 8:01 am     Reply with quote

I would try to find out exactly what in the Zigbee module dies. You probably don't have a schematic, but maybe you can look up part numbers and find power buses and clock lines. Is the Zigbee still regulating power? Is the clock still running? Is it generating RF? These questions may tell you what has failed and maybe why it has failed.
_________________
The search for better is endless. Instead simply find very good and get the job done.
jecottrell



Joined: 16 Jan 2005
Posts: 559
Location: Tucson, AZ

View user's profile Send private message

PostPosted: Mon Jan 03, 2011 8:46 am     Reply with quote

I think I recall I had a similar problem with XBees. I did a lot of work with them in close proximity and never reset their default power levels to the lowest possible. Once I changed them to the lowest possible power setting for prototyping, I haven't had the problem again.
hayee



Joined: 05 Sep 2007
Posts: 252

View user's profile Send private message

PostPosted: Tue Jan 04, 2011 1:01 am     Reply with quote

Thanks for all your suggestions

The IC used in the module is EM260 processor (from EMBER).

I checked the power at the EM260 it is 3.3v
I checked the waveform of crystal, it shows waveform then shows 0v then shows waveform then shows 0v and it continues.
Due to this reason all other process are not working. Now what to do?
Ttelmah



Joined: 11 Mar 2010
Posts: 19509

View user's profile Send private message

PostPosted: Tue Jan 04, 2011 5:21 am     Reply with quote

So you are saying that on pin 38 of the ember unit, you are seeing an 'intermittent' clock, with a burst of clock, then it stopping?.
Have you checked the voltage on the 1.8v regulator?.
What is the interval between the bursts?.

If the interval is about 2 seconds, it suggests the chip is performing a watchdog reset.
The 1.8v goes 'off', if the chip goes into 'deep sleep' mode. Hence testing this would be informative.

Best Wishes
hayee



Joined: 05 Sep 2007
Posts: 252

View user's profile Send private message

PostPosted: Wed Jan 05, 2011 10:54 pm     Reply with quote

Quote:
you are seeing an 'intermittent' clock, with a burst of clock, then it stopping?.

Its not exactly that. Its like fluctuation but very fast.

Quote:
Have you checked the voltage on the 1.8v regulator?.

I haven't find any 1.8 regulator on the board but some of the pins of em260 shows 1.8v
but the values of these voltages also varying between 1.74 to 1.8v.
bkamen



Joined: 07 Jan 2004
Posts: 1615
Location: Central Illinois, USA

View user's profile Send private message

PostPosted: Wed Jan 05, 2011 11:07 pm     Reply with quote

temtronic wrote:
Never, ever seen code destroy a computer.It's just 1s and 0s !



Back in the 80's -- Supposedly there was code that could cause a C64 to fry some critical components.

Since I owned an Atari800, I was safe. ;)

-Ben
_________________
Dazed and confused? I don't think so. Just "plain lost" will do. :D
Ttelmah



Joined: 11 Mar 2010
Posts: 19509

View user's profile Send private message

PostPosted: Thu Jan 06, 2011 5:24 am     Reply with quote

The 1.8v regulator, is part of the em260. Used internally for just about everything!. Only time it should drop significantly, is if the unit is going to deep sleep, or doing a power reset. It should be coming out on pin12, and this should be connected back to pin14, and to pins 1, 4, & 7, where it feeds the VCO, RF generator, and the IF stage, also to 32, 36, 37, & 40, where it feeds the crystal oscillator, the internal synthesiser, and the main logic. If this fluctuates significantly, it'll prevent large parts of the circuit from working (it is allowed to be as low as 1.7v, or as high as 1.9, but it needs to be _stable_ when the unit is running).....
Comes back to the question about 'intervals' on the fluctuations. Again, about 2 seconds, could imply a watchdog timeout....

Best Wishes
hayee



Joined: 05 Sep 2007
Posts: 252

View user's profile Send private message

PostPosted: Fri Jan 07, 2011 4:31 am     Reply with quote

Quote:
about 2 seconds, could imply a watchdog timeout

No its not 2 seconds. Maybe its time is less than 1 sec.

Actually what is happening is that the waveform is switching between the ground and the signal. I cannot measure the time delay by scope even if I increase or decrease the time division on the scope. Also the amplitude of the wavefrom is very low. Its amplitute is 680mV.

Maybe I am unable to be clear to you about what I am trying to say.
I don't know how to explain exactly.
anh_risn



Joined: 05 Jun 2011
Posts: 4

View user's profile Send private message

PostPosted: Wed Sep 07, 2011 3:20 am     Reply with quote

Hi hayee, have you solve the problem?
I also encountered same problem like you do.
The zigbee suddenly broken after working for a while.
Seems like the zigbee cannot pass the EmberInitialization() function.
It gets stuck in the while loop inside EM260Reset() function.
I also check the regulator on the EM260 chip, it shows ok 1.8V
bkamen



Joined: 07 Jan 2004
Posts: 1615
Location: Central Illinois, USA

View user's profile Send private message

PostPosted: Mon Sep 12, 2011 9:50 pm     Reply with quote

temtronic wrote:
Never, ever seen code destroy a computer.It's just 1s and 0s !


If I remember right, there used a virus for Commodore64's that could put the system in a state to damage chips...

I didn't own one though, so no verification on that one. :P

-Ben
_________________
Dazed and confused? I don't think so. Just "plain lost" will do. :D
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group