CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com
convert Decimal to Hex
Goto page 1, 2  Next
 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
nemero16



Joined: 21 Nov 2009
Posts: 19

View user's profile Send private message

convert Decimal to Hex
PostPosted: Sat Nov 21, 2009 7:45 pm     Reply with quote
Hi, I have written a program in C which writes an eeprom with uart, but I want to write address in decimal and not hex. When I use the uart command R and W ...example: read or write?:r block:125(instead of writing 7D) byte:AABBCCDD... as I can do? This is the code:

main.c :
Code:

#include <16F876.h>
#device adc=8

#FUSES NOWDT                    //No Watch Dog Timer
#FUSES HS                       //High speed Osc (> 4mhz for PCM/PCH) (>10mhz for PCD)
#FUSES NOPUT                    //No Power Up Timer
#FUSES NOPROTECT                //Code not protected from reading
#FUSES NOBROWNOUT               //No brownout reset
#FUSES NOLVP                    //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O
#FUSES NOCPD                    //No EE protection
#FUSES NOWRT                    //Program memory not write protected
#FUSES NODEBUG                  //No Debug mode for ICD

#use delay(clock=4000000)
#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8,stream=seriale1)
#use i2c(Master,Fast,sda=PIN_C4,scl=PIN_C3)

#include "input.c"
#include "2416.c"

void main()
{BYTE *value[4], cmd;
   EEPROM_ADDRESS address;
   unsigned long int x;
   

   init_ext_eeprom();

   do {
      do {
         printf("\r\Read or Write?: ");
         cmd=getc();
         cmd=toupper(cmd);
         putc(cmd);
      } while ( (cmd!='R') && (cmd!='W') && (cmd!='T') );

     if((cmd!='R') && (cmd!='W')){
     }
     else{
     printf("\n\rBlock: ");
     
#if sizeof(EEPROM_ADDRESS)==1
      address = gethex();
#else
#if EEPROM_SIZE>0xfff
      address = gethex();
#else
      address = gethex1();
#endif
      address = (address<<8)+gethex();
#endif}

    if(cmd=='R'){
     unsigned int i;
     unsigned int n=4;
     READ_EXT_EEPROM( address, n);
       printf("\r\nByte: ");
         for (i=0; i<n; i++) {
           printf("%X", data[i]);
         }
         printf("\r\n");
      }

    if(cmd=='W'){
     unsigned int i;
     unsigned int n=4;
         printf("\r\nByte: ");
         for(i=0; i<n; i++){
         value[i]=gethex();}
         WRITE_EXT_EEPROM( address, value, n);
          printf("\r\n");
         }
         
    if(cmd=='T'){
     int i;
     unsigned int8 a;
     unsigned int max_memory=128;
     int n_byte_letti=4;
       printf("\r\n");
       printf("\r\n");
       for (a=0; a<max_memory; a+=n_byte_letti) {
       read_total_ext_eeprom(a, n_byte_letti);
       printf("%u%c",a,')');
       for (i=0; i<n_byte_letti; i++) {
        printf("%X", data[i]);
       }
       printf(" ");
     }
     printf("\r\n");
     }
     } while(true);
}


and this is 2416.c:
Code:
#ifndef EEPROM_SDA

#define EEPROM_SDA  PIN_C4
#define EEPROM_SCL  PIN_C3

#endif


#use i2c(master, sda=EEPROM_SDA, scl=EEPROM_SCL)

#define EEPROM_ADDRESS unsigned int8
#define EEPROM_SIZE    1024

BYTE data[4];

void init_ext_eeprom() {
   output_float(EEPROM_SCL);
   output_float(EEPROM_SDA);
}

int1 ext_eeprom_ready() {
   int1 ack;
   i2c_start();            // If the write command is acknowledged,
   ack = i2c_write(0xa0);  // then the device is ready.
   i2c_stop();
   delay_ms(10);
   return !ack;
}

void write_ext_eeprom(EEPROM_ADDRESS address, BYTE *data[4], unsigned int n_byte)
{int i;

if (n_byte>4) n_byte=4;
if (n_byte==0) return;
   while(!ext_eeprom_ready());
   i2c_start();
   i2c_write(0xa0);
   i2c_write(address);
for(i=0; i<n_byte; i++){
i2c_write(data[i]);}
i2c_stop();
delay_ms(10);}


void read_ext_eeprom(EEPROM_ADDRESS address, unsigned int n_byte)
{int i;
  if (n_byte>4) n_byte=4;
if (n_byte==0) return;
 while(!ext_eeprom_ready());
   i2c_start();
   i2c_write(0xa0);
   i2c_write(address);
   i2c_start();
   i2c_write(0xa1);
for (i=0; i<n_byte; i++) {
data[i]=i2c_read(1);}
i2c_stop();
delay_ms(10);
return;
}

void read_total_ext_eeprom(EEPROM_ADDRESS address, unsigned int n_byte)
{int i;
  if (n_byte>4) n_byte=4;
if (n_byte==0) return;
 while(!ext_eeprom_ready());
   i2c_start();
   i2c_write(0xa0);
   i2c_write(address);
   i2c_start();
   i2c_write(0xa1);
for (i=0; i<n_byte; i++) {
data[i]=i2c_read(1);}
i2c_stop();
delay_ms(10);
return;
}
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sat Nov 21, 2009 9:29 pm     Reply with quote
This CCS driver file has routines to get input from a terminal in other
ways than just Hex format. For example, you can get a number in
decimal integer format. Here is the file location:
Quote:
c:\program files\picc\drivers\input.c


Also, it looks like you have modified the external eeprom routines,
and you have made mistakes. If you need routines to read and write
to an external eeprom, look in this file:
Quote:
c:\program files\picc\drivers\external_eeprom.c


Use the CCS routines. That's why CCS included them with the compiler -
To make it easier to do the things you need.
nemero16



Joined: 21 Nov 2009
Posts: 19

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 6:21 am     Reply with quote
Yes, I have modified the library to add an EEPROM array... can you tell me where I made mistakes? I analyzed the input file that is included in my program but I do not know how to set it ... give me some help?
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 10:39 am     Reply with quote
Quote:
void main()
{
BYTE *value[4], cmd;


void write_ext_eeprom(EEPROM_ADDRESS address, BYTE *data[4], unsigned int n_byte)

In various places you have defined an array of pointers and it's clear
that you don't want an array of pointers, you want an array of bytes.
Get rid of the '*' in all your array declarations.

Quote:
void read_ext_eeprom(EEPROM_ADDRESS address, unsigned int n_byte)
.
.
.
for (i=0; i<n_byte; i++) {
data[i]=i2c_read(1);}

i2c_stop();
delay_ms(10);
return;
}

In this function you are reading 4 bytes, but don't have a "NACK" on
the last read in the sequence. This NACK is required by the i2c
specification. In CCS, a NACK is done by giving the i2c_read() function
a parameter of 0.

Also, functions return automatically. You don't need a return statement
at the end.
nemero16



Joined: 21 Nov 2009
Posts: 19

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 12:18 pm     Reply with quote
mmm ok I have removed all the "*", although I've set for reading i2c_read (1) function I have no problem, if imposed i2c_read (0) function works the same? to convert from decimal to hex as I set the gethex ()?
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 3:22 pm     Reply with quote
You have created your own (buggy) routines to read and write 4 bytes to
eeprom. You don't need to do that. CCS has routines to do this.
These routines are in the external_eeprom.c file:
Quote:

write_int32_ext_eeprom()
read_int32_ext_eeprom()


If you want to get the address in decimal, then use the get_int()
or get_long() routines in the input.c file. Use one of those routines
instead of the get_hex() routines.
nemero16



Joined: 21 Nov 2009
Posts: 19

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 3:35 pm     Reply with quote
But there is this in input.c file, but not get_int ():
Code:
#include <ctype.h>

BYTE gethex1() {
   char digit;

   digit = getc();

   putc(digit);

   if(digit<='9')
     return(digit-'0');
   else
     return((toupper(digit)-'A')+10);
}

BYTE gethex() {
   unsigned int8 lo,hi;
   
   hi = gethex1();
   lo = gethex1();
   
   if(lo==0xdd)
     return(hi);
   else
     return( hi*16+lo );
}

void get_string(char* s, unsigned int8 max) {
   unsigned int8 len;
   char c;

   --max;
   len=0;
   do {
     c=getc();
     if(c==8) {  // Backspace
        if(len>0) {
          len--;
          putc(c);
          putc(' ');
          putc(c);
        }
     } else if ((c>=' ')&&(c<='~'))
       if(len<=max) {
         s[len++]=c;
         putc(c);
       }
   } while(c!=13);
   s[len]=0;
}

// stdlib.h is required for the ato_ conversions
// in the following functions
#ifdef _STDLIB
#if !defined(__PCD__)
signed int8 get_int() {
  char s[5];
  signed int8 i;

  get_string(s, 5);

  i=atoi(s);
  return(i);
}
#endif

#if defined(__PCD__)
signed int16 get_int() {
  char s[5];
  signed int16 i;

  get_string(s, 7);

  i=atoi(s);
  return(i);
}
#endif

#if !defined(__PCD__)
signed int16 get_long() {
  char s[7];
  signed int16 l;

  get_string(s, 7);
  l=atol(s);
  return(l);
}
#endif

#if defined(__PCD__)
signed int32 get_long() {
  char s[7];
  signed int32 l;

  get_string(s, 10);
  l=atoi32(s);
  return(l);
}
#endif

float get_float() {
  char s[20];
  float f;

  get_string(s, 20);
  f = atof(s);
  return(f);
}

#endif
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 3:49 pm     Reply with quote
Quote:
signed int8 get_int() {

Look more closely.
nemero16



Joined: 21 Nov 2009
Posts: 19

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 3:53 pm     Reply with quote
ops... Very Happy I had not seen .. hahaha, but writing this out an error ...:
address = get_int();
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 4:19 pm     Reply with quote
Read the input.c file comments above the get_int() function. It says:
Quote:

// stdlib.h is required for the ato_ conversions
// in the following functions


This means you have to include the stdlib.h file, as shown below:
Quote:

#include <stdlib.h>
#include "input.c"
#include "2416.c"
nemero16



Joined: 21 Nov 2009
Posts: 19

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 4:34 pm     Reply with quote
compiles ok but the program does not work because when I enter the address in dec and it does not go on .... this is the code:
Code:
#include <16F876.h>
#device adc=8

#FUSES NOWDT                    //No Watch Dog Timer
#FUSES HS                       //High speed Osc (> 4mhz for PCM/PCH) (>10mhz for PCD)
#FUSES NOPUT                    //No Power Up Timer
#FUSES NOPROTECT                //Code not protected from reading
#FUSES NOBROWNOUT               //No brownout reset
#FUSES NOLVP                    //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O
#FUSES NOCPD                    //No EE protection
#FUSES NOWRT                    //Program memory not write protected
#FUSES NODEBUG                  //No Debug mode for ICD

#use delay(clock=4000000)
#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8,stream=seriale1)
#use i2c(Master,Fast,sda=PIN_C4,scl=PIN_C3)

#include <stdlib.h>
#include "input.c"
#include "2416.c"

void main()
{BYTE value[4], cmd;
   unsigned int8 address;
   

   init_ext_eeprom();

   do {
      do {
         printf("\r\nLeggi o Scrivi?: ");
         cmd=getc();
         cmd=toupper(cmd);
         putc(cmd);
      } while ( (cmd!='L') && (cmd!='S') && (cmd!='T') );

     if((cmd!='L') && (cmd!='S')){
     }
     else{
     printf("\n\rBlocco: ");
     address = get_int();
     
#if sizeof(EEPROM_ADDRESS)==1
    address = get_int(); 
#else
#if EEPROM_SIZE>0xfff
      address = get_int();
#else
      address = get_int();
#endif
      address = (address<<8)+get_int();
#endif}

    if(cmd=='L'){
     unsigned int i;
     unsigned int n=4;
     READ_EXT_EEPROM( address, n);
       printf("\r\nByte: ");
         for (i=0; i<n; i++) {
           printf("%X", data[i]);
         }
         printf("\r\n");
      }

    if(cmd=='S'){
     unsigned int i;
     unsigned int n=4;
         printf("\r\nByte: ");
         for(i=0; i<n; i++){
         value[i]=gethex();}
         WRITE_EXT_EEPROM( address, value, n);
          printf("\r\n");
         }
         
    if(cmd=='T'){
     int i;
     unsigned int8 a;
     unsigned int max_memory=128;
     int n_byte_letti=4;
       printf("\r\n");
       printf("\r\n");
       for (a=0; a<max_memory; a+=n_byte_letti) {
       read_total_ext_eeprom(a, n_byte_letti);
       printf("%u%c",a,')');
       for (i=0; i<n_byte_letti; i++) {
        printf("%X", data[i]);
       }
       printf(" ");
     }
     printf("\r\n");
     }
     } while(true);
}
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 5:03 pm     Reply with quote
My advice is to simplify your program. Cut out large sections of your
code and make it smaller. Test each little piece of the program.
Prove that it works. Then put it together again.
nemero16



Joined: 21 Nov 2009
Posts: 19

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 5:09 pm     Reply with quote
But the program works and also good ... it's just that I want to insert the address in decimal and not hex ... the part to change, or insert the get_int () is this:
Code:

void main()
{BYTE *value[4], cmd;
   EEPROM_ADDRESS address;
   
   init_ext_eeprom();

   do {
      do {
         printf("\r\Read or Write?: ");
         cmd=getc();
         cmd=toupper(cmd);
         putc(cmd);
      } while ( (cmd!='R') && (cmd!='W') && (cmd!='T') );

     if((cmd!='R') && (cmd!='W')){
     }
     else{
     printf("\n\rBlock: ");
     
#if sizeof(EEPROM_ADDRESS)==1
      address = gethex();
#else
#if EEPROM_SIZE>0xfff
      address = gethex();
#else
      address = gethex1();
#endif
      address = (address<<8)+gethex();
#endif}
........
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 5:14 pm     Reply with quote
Quote:

#if sizeof(EEPROM_ADDRESS)==1
address = gethex();
#else
#if EEPROM_SIZE>0xfff
address = gethex();
#else
address = gethex1();
#endif
address = (address<<8)+gethex();
#endif}
........

Decide which line you want to use, and get rid of all the other lines,
and get rid of all the #if, #ifdef, #else, and #endif lines.

And change the line to address = get_int();
nemero16



Joined: 21 Nov 2009
Posts: 19

View user's profile Send private message

PostPosted: Sun Nov 22, 2009 5:57 pm     Reply with quote
ok, I removed everything and I left this:
Code:
   if ((cmd = 'L') & & (cmd = 'S')) {
     }
     else {
     printf ( "\ n \ rBlocco:");
     address = gethex();}


but when I go to write address = get_int () the program crashes and does not go forward .. I should set it first receives the value in decimal and then convert it to hex ...how can I do?
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group