CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com

SPI 16B address and 8b data

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
beaker404



Joined: 24 Jul 2012
Posts: 163

View user's profile Send private message

SPI 16B address and 8b data
PostPosted: Mon Aug 15, 2022 12:20 pm     Reply with quote

CCS 5.064
PIC18F26K22
EEPROM 93LC66C

Looked around the forum and nothing came out as an exact solution to my problem,
problem being, using a 93LC66 in 8b data mode so 512 x 8 bytes.
Communication is via SPI and works find IF I stay below an address of 255
and I know why, the SPI is only sending 8b of address, tried sending MSB and LSB of the address word, did not work.
Is there a way to get a 16b address to the EEPROM followed by the 8b data? Perhaps I just do not get SPI well enough to resolve it.

SPI set up like this: for 8b data, this all works just not when I try to do 16b addressing.
Code:

#DEFINE SPI_XFER_9356(x)   spi_xfer(SPI2_EEPROM, x)

#DEFINE  EEPROM_ADDRESS unsigned long

#use spi(master, DO=Pin_B3, CLK=PIN_B1, DI=PIN_B2 ,ENABLE_ACTIVE=1, ENABLE_DELAY=20,mode=0, baud=2000000, stream=SPI2_EEPROM, bits=8, FORCE_SW)


my write function:
Code:
void write_ext_eeprom(EEPROM_ADDRESS address, BYTE data)
{

  disable_interrupts(global);           

   output_high(EEPROM_SELECT);
   
   SPI_XFER_9356(0xa);
   
   SPI_XFER_9356(address);
 
   
   SPI_XFER_9356(data);
   
   
   output_low(EEPROM_SELECT);
   
   delay_ms(11);
   enable_interrupts(global);
}


my read function:
Code:
BYTE read_ext_eeprom(EEPROM_ADDRESS address)
{
   BYTE data;
   
   disable_interrupts(global);           
   
   output_high(EEPROM_SELECT);
   
   SPI_XFER_9356(0xc);
   
   SPI_XFER_9356(address);
   
   data=SPI_XFER_9356(0);
   
   
   output_low(EEPROM_SELECT);

   enable_interrupts(global);           
   return(data);

}
beaker404



Joined: 24 Jul 2012
Posts: 163

View user's profile Send private message

PostPosted: Mon Aug 15, 2022 12:22 pm     Reply with quote

sorry for the poor formatting of the thread, for some reason I cannot edit it now correctly.
gaugeguy



Joined: 05 Apr 2011
Posts: 286

View user's profile Send private message

PostPosted: Mon Aug 15, 2022 12:43 pm     Reply with quote

To access addresses 256-511, the high address bit is the low bit of the command.

Code:

output_high(EEPROM_SELECT);

SPI_XFER_9356(0x0c | 0x01);  // command and high bit of address

SPI_XFER_9356(address);  // low 8 bits of address

data=SPI_XFER_9356(0);


output_low(EEPROM_SELECT);
beaker404



Joined: 24 Jul 2012
Posts: 163

View user's profile Send private message

PostPosted: Mon Aug 15, 2022 1:14 pm     Reply with quote

thanks.
Not sure how I missed that in the datasheet,
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group