CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com
Help to fix this error undefined identifier Motor_M1_On

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
vineel



Joined: 19 Apr 2016
Posts: 2

View user's profile Send private message

Help to fix this error undefined identifier Motor_M1_On
PostPosted: Tue Apr 19, 2016 3:57 am     Reply with quote
Hi! i am writing a code for joystick based wheel chair, using pic16f73.
Everything is fine, but i am getting a set of errors such as undefined identifiers Motor_M1_On, etc., which are related to dc motor.
My code is as follows:
Code:

#include <16F73.h>
#include <stdlib.h>
#include <Motor.h>

#fuses HS, NOWDT, BROWNOUT, PROTECT, PUT
#use delay(oscillator=20M)

unsigned long duty = 0;

void dowork(unsigned int x)
{
   switch(x)
   {           
   
    case 116:
            if(!input(pin_A0))
            {
           
             set_pwm1_duty(700);
             set_pwm2_duty(700);
                     
             Motor_M1_On(150,1); //1=forward, 0=reverse
             Motor_M2_On(150,1); //1=forward, 0=reverse
            }
             break;
             
    case 117:
             set_pwm1_duty(700);
             set_pwm2_duty(700);
           
             Motor_M1_On(150,0); //1=forward, 0=reverse
             Motor_M2_On(150,0); //1=forward, 0=reverse
             break;             
   
    case 51:             
             Set_pwm1_duty(550); //fixed duty for turnings
             Set_pwm2_duty(550); //fixed duty for turnings
             output_high(PIN_C5);
             Motor_M1_On(100,0); //1=forward, 0=reverse
             Motor_M2 On(100,1); //1=forward, 0=reverse
             break;
   
    case 52:
             set_pwm1_duty(550);  //fixed duty for turnings
             set_pwm2_duty(550);  //fixed duty for turnings
             output_high(PIN_C6);
             Motor_M1_On(100,1); //1=forward, 0=reverse
             Motor_M2_On(100,0); //1=forward, 0=reverse
             break;
   
   }
}


void Motor_M1(int direction)
{
      delay_ms(10);
      if(direction == 1) //Forward
      {
         output_low(PIN_C0);
         output_high(PIN_C5);
      }
      if(direction == 0) //Reverse
      {
         output_low(PIN_C1);
         output_high(PIN_C5);
      }
      delay_ms(100);
}

void Motor_M2(int direction)
{
      if(direction == 1) //Forward
      {
         output_low(PIN_C0);
         output_high(PIN_C6);
      }
      if(direction == 0) //Reverse
      {
         output_low(PIN_C1);
         output_high(PIN_C6);         
      }
      delay_ms(100);
}


void main()
{
   unsigned long int x=0;
   unsigned long int y=0;

   //Microcontroller Health Check
 
   output_high(PIN_C5);
   output_high(PIN_C6);
   delay_ms(1000);
 
   output_low(PIN_C5);
   output_low(PIN_C6);
   delay_ms(1000);
 
   output_high(PIN_C5);
   output_high(PIN_C6);
   delay_ms(1000);
 
   output_low(PIN_C5);
   output_low(PIN_C6);

   setup_adc(ADC_CLOCK_INTERNAL);   //enables the a/d module
   setup_adc_ports(ALL_ANALOG);   //sets all the adc pins to analog
   
   //PWM Settings
   
    setup_timer_2(T2_DIV_BY_16, 127, 1);
    setup_ccp1(CCP_PWM);
    set_pwm1_duty(620);
    setup_ccp2(CCP_PWM);    //pwm setting for motor 2
    set_pwm2_duty(620);
     
   while(1)
   {
      set_adc_channel(1);
      delay_ms(1);
      y = read_adc();
      delay_ms(1);
      set_adc_channel(0);
      delay_ms(1);
      x = read_adc();
      delay_ms(1);
     
      set_pwm1_duty(600);
      set_pwm2_duty(600);
      if(y < 80)
      {
          output_high(PIN_C5); //LED on
          Motor_M1(0);
          Motor_M2(0);
         
      }
      else if(y > 100)
      {
          output_high(PIN_C6);
          Motor_M1(1);
          Motor_M2(1);
     
      }     
      else if(x < 80)
         {
            output_high(PIN_C5);
            Motor_M1(1);
            Motor_M2(0);
         }
      else if(x > 100)
         {
            output_high(PIN_C6);
            Motor_M1(0);
            Motor_M2(1);
         }
           
     set_pwm1_duty(0);
     set_pwm2_duty(0);
   
     output_low(PIN_C5);
     output_low(PIN_C6);
   }   
}

Can anyone help me to fix this and suggest me right header file for dc motor control ?
_________________
vineel
RF_Developer



Joined: 07 Feb 2011
Posts: 839

View user's profile Send private message

PostPosted: Tue Apr 19, 2016 4:36 am     Reply with quote
At this simple level, with only a few routines, I'd suggest not using a header file at all.

The errors you describe are because the do-work routine calls routines that are not defined/declared. But that's no more than the error message says so that should nto be a surprise.

It doesn't matter that you don't call do_work() anywhere; if it's there at all, the routines it calls, such as Motor_M1_On and Motor_M2_On, have to be defined somewhere and they aren't.

It sounds as if you are confused over basic C code structure: how, why and where routines are defined. For that you need to read a C language book or tutorial.
vineel



Joined: 19 Apr 2016
Posts: 2

View user's profile Send private message

PostPosted: Tue Apr 19, 2016 4:48 am     Reply with quote
RF_Developer wrote:
At this simple level, with only a few routines, I'd suggest not using a header file at all.

The errors you describe are because the do-work routine calls routines that are not defined/declared. But that's no more than the error message says so that should nto be a surprise.

It doesn't matter that you don't call do_work() anywhere; if it's there at all, the routines it calls, such as Motor_M1_On and Motor_M2_On, have to be defined somewhere and they aren't.

It sounds as if you are confused over basic C code structure: how, why and where routines are defined. For that you need to read a C language book or tutorial.


So do i need to define the motors m1 and m2 ? I don't have much time to work on it, and for going through books and tutorial and by the way i'm newbie. Would you be kind enough to help me with this ? I mean can you provide me small sample so that i can understand ? Anyway thanks for your help bro.
_________________
vineel
RF_Developer



Joined: 07 Feb 2011
Posts: 839

View user's profile Send private message

PostPosted: Tue Apr 19, 2016 5:23 am     Reply with quote
Quote:
by the way i'm newbie


That's blatantly obvious. It's also obvious, from the formatting, that the code you posted is cut and pasted from at least two sources. The PIC you are using is one of the very earliest flash-based parts, and has been effectively obsolete for many years, but is still used occasionally for teaching purposes.

To get rid of the errors, delete the do_work routine. There may well be some errors, different to the ones you've reported, but the one's you've reported will be gone.

There are severla problems with your code, including but by no means limited to the ADC set-up. Hint: ADC_CLOCK_INTERNAL is not recommended except under very specific circumstances.

I'd expect any practical wheelchair controller to give fully proportional control, most likely by a PID loop, probably with some sort of creep/nudge capability, all of which is fully safety interlocked.

So, all that considered, this is a late college assignment, isn't it?
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group