CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com
Problem with serial on 12f629

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
diegostreetbob



Joined: 05 Sep 2009
Posts: 11

View user's profile Send private message Send e-mail MSN Messenger

Problem with serial on 12f629
PostPosted: Wed Nov 17, 2010 3:27 pm     Reply with quote
Hello friends,
I have a great problem with serial output, the hyperterminal shows for
example with printf("hola"); it shows ÷ symbol and with putc("hola");
it shows VHº symbol.

This is the code, the last line is printf("hola");
The hyperterminal is configured with 2400 8N1 hardware control.
Thanks in advance...
Code:

#include <12F629.h>
#FUSES NOWDT                    //No Watch Dog Timer
#FUSES INTRC_IO                 //Internal RC Osc, no CLKOUT
#FUSES NOCPD                    //No EE protection
#FUSES NOPROTECT                //Code not protected from reading
#FUSES MCLR                     //Master Clear pin enabled
#FUSES NOPUT                    //No Power Up Timer
#FUSES NOBROWNOUT               //No brownout reset
#FUSES BANDGAP_HIGH         
#FUSES RESERVED                 //Used to set the reserved FUSE bits
#use delay(internal=4000000)

#use rs232(baud = 2400,parity=N,xmit=PIN_A1,bits=8)

#byte porta=0x05
#byte trisa=0x85

#use fast_io(a)

#define GP0 PIN_A0
#define GP1 PIN_A1
#define GP2 PIN_A2
#define GP3 PIN_A3
#define GP4 PIN_A4
#define GP5 PIN_A5

#zero_ram

int lectura(); //funcion lectura
int1 detecta(void); //funcion detectar pulso bajo
void memo(int v); //funcion memo, en v se almacenara el valor de leido una vez pulsado memo
void compara(int w); //función compara lectura con datos de eprom para identificar boton
int boton;
int boton1,boton2,boton3; //variable numero boton
int leido;

void main()
{
   set_tris_a(0b110000);
   int1 detectado;//recibira el valor del flagdetecta mediante el return de la funcion detecta()
   setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1);
   setup_timer_1(T1_INTERNAL|T1_DIV_BY_1);
   set_timer1(0);

while(true)
{
if(bit_test(porta,4)==0) memo(leido);
else detectado=detecta();//llamada funcion detecta,y almacenado mediante el return el valor de flag detecta
leido=lectura();//llamamos funcion lectura y cargamos leido con valor y de lectura Return(y)
compara(leido);//llamamos a compara y le enviamos el valor de leido
}
}

int1 detecta(void)
{
int1 flagdetecta; //variable que se pondrá a 1 cuando haya sido detectado

star:
if(bit_test(porta,4)==0) memo(leido);//va a memorizar si pulsamos memo
set_timer1(0);
while(bit_test(porta,5)==0) //cuando el pulso es bajo, leemos el timer1 para medir el ancho de pulso
{
if(get_timer1()>18000)//retardo para detectar primer pulso largo bajo del mando
{
flagdetecta=1;//detectado
return(flagdetecta);//devolvemos el 1 de flagdetecta
}
}
goto star;
}

int lectura()
{
output_high(pin_a1);//para disparo del ikalogic

int codigo[3]; // Array de [3]Bytes, 24bits para la lectura del código boton1
int x; //para el for-next y lectura del array
int y;//almacenaremos codigo0+codigo1+codigo2

for(x=0;x<21;x++)//leemos 22bits, los 4 que faltan los obviamos con el retardo de 8000 de la linea 59.
{
delay_us(2439);//retardo para conincidir con el flanco tren de impulsos
shift_left(codigo,3,bit_test(porta,5));//registra lo que entra por portc,0 en los 2 bytes del array código
}

output_low(pin_a1);//para disparo ikalogic
y=codigo[0]+codigo[1]+codigo[2];
set_timer1(0);

output_low(pin_a0);//para encender el led hay que sacar 0
delay_ms(250);
output_high(pin_a0);
delay_ms(250);
output_low(pin_a0);//para encender el led hay que sacar 0
delay_ms(250);
output_high(pin_a0);
return(y);
}

void memo(int v)
{
boton++;//aunmenta una vez cada vez que entra en la funcion

if(boton>3) boton=1;

switch(boton)//depende las veces que se haya pulsado el boton de grabar se graba en una posición distinta
{
case 1:
write_eeprom(0x00,v);//grabamos leido(asignado a V) en la eprom
break;
case 2:
write_eeprom(0x01,v);
break;
case 3:
write_eeprom(0x02,v);
break;
}

{
output_low(pin_a0);
delay_ms(1000);
output_high(pin_a0);
delay_ms(1000);
output_low(pin_a0);
delay_ms(1000);
output_high(pin_a0);
}
}

void compara(int w)
{
output_low(pin_a0);//para encender el led hay que sacar 0
delay_ms(50);
output_high(pin_a0);
delay_ms(50);
output_low(pin_a0);//para encender el led hay que sacar 0
delay_ms(50);
output_high(pin_a0);

printf("hola");
}
jds-pic



Joined: 17 Sep 2003
Posts: 205

View user's profile Send private message

Re: Problem with serial on 12f629
PostPosted: Wed Nov 17, 2010 3:54 pm     Reply with quote
diegostreetbob wrote:

problem with serial output, the hyperterminal

please use another tool for debugging serial problems. Hyperterminal is not a good, reliable program for effective debugging. Using TeraTerm or similar is a much better plan.

diegostreetbob wrote:

The hyperterminal is configured with 2400 8N1 hardware control.

You should not be using hardware flow control; you should be using "no flow control".

diegostreetbob wrote:

Code:

#use delay(internal=4000000)

what frequency is your board's oscillator?

diegostreetbob wrote:

Code:

#use rs232(baud = 2400,parity=N,xmit=PIN_A1,bits=8)
#byte porta=0x05
#byte trisa=0x85
#use fast_io(a)
#define GP1 PIN_A1
...
output_high(pin_a1);//para disparo del ikalogic
...
output_low(pin_a1);//para disparo ikalogic

why are you defining pin A1 as for use by RS232, and then playing with it via output_high/output_low?

jds-pic
Ttelmah



Joined: 11 Mar 2010
Posts: 19369

View user's profile Send private message

PostPosted: Thu Nov 18, 2010 5:34 am     Reply with quote
Add some further comments.
What voltage are you running the PIC at?. If not 5v, how accurate is the 12F629 internal oscillator warranted to be?. Is this good enough for RS232?.
What circuitry are you using to connect the PIC to the PC?. You something to provide the voltage shift, and inversion.

Best Wishes
diegostreetbob



Joined: 05 Sep 2009
Posts: 11

View user's profile Send private message Send e-mail MSN Messenger

PostPosted: Thu Nov 18, 2010 2:15 pm     Reply with quote
Ok,
tomorrow i will check all, thanks.
diegostreetbob



Joined: 05 Sep 2009
Posts: 11

View user's profile Send private message Send e-mail MSN Messenger

PostPosted: Fri Nov 19, 2010 2:37 pm     Reply with quote
Today I've tested and work fine.

Change the baudrate at 300 and no flow control, and only play with pin_a1 for tx.

Thanks

Best regards
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group