![](templates/subSilver/images/CCSLogo.jpg) |
![CCS C Software and Maintenance Offers](templates/subSilver/images/forumAd6.jpg) |
View previous topic :: View next topic |
Author |
Message |
assaad
Joined: 09 Dec 2009 Posts: 37
|
External parallel ram problem |
Posted: Tue Aug 24, 2010 4:01 am |
|
|
Hi all
It was long time for me, but finally I am back with new project full of mistakes and need your help friends.
I am using 128k external parallel ram (AS6C1008) with 18f8722. The problem that I have problem with reading and writing to the ram, it works sometimes and does not alot. I think I have mistake in hardware maybe ! or a software bug because I am new to CCS .
The routines that I use for RAM :
Code: |
////////////////////////////////////////////////////////
byte ram_read_high(int16 address )
{
int8 value;
byte data ;
output_h(0xd0); // 0110 ce , ce2 , we, oe disable ram
output_high(pin_g0); // A16=0 ///
output_high(pin_j2);
output_low(pin_g3); // enable latch to ram ///oelram of 74hc573
value = make8(address,0); // low byte
trise=0;
trisd=0;
late=value;
//output_e(value);
value = make8(address,1); // high byte
latd=value;
//output_d(value);
output_h(0x60); // 0110 ce , ce2 , we, oe enable ram
output_high(pin_g3); // disable latch to ram ///oelram of 74hc573
trise=0xff;
data=porte;
//data=input_e();
output_h(0xd0); // 0110 ce , ce2 , we, oe disable ram
output_low(pin_g0); // A16=0 ///
output_low(pin_j2);
return (data);
}
void ram_write_high(int16 address , byte data)
{
int8 value , test,counter;
counter=0;
start_write:
output_h(0xd0); // 0110 ce , ce2 , we, oe disable ram
output_high(pin_g0); // A16=0 ///
output_high(pin_j2);
value = make8(address,0); // low byte
trise=0;
trisd=0;
late=value;
//output_e(value);
value = make8(address,1); // high byte
latd=value;
//output_d(value);
output_low(pin_g3); // enable latch to ram ///oelram of 74hc573
//#asm
//nop
//#endasm
output_h(0x10); // 0100 ce , ce2 , we, oe enable ram
//#asm
//nop
//#endasm
output_h(0x20); // 0100 ce , ce2 , we, oe enable ram
output_high(pin_g3); // disable latch to ram ///oelram of 74hc573
late=data;
//output_e(data);
output_h(0xd0); // 0110 ce , ce2 , we, oe disable ram
output_low(pin_g0); // A16=0 ///
output_low(pin_j2);
}
|
I would like to upload the schematic but I could not find an option to do that.
I wish someone guide me to solve the ram issue and thanks in advanced. |
|
![](templates/subSilver/images/spacer.gif) |
PCM programmer
Joined: 06 Sep 2003 Posts: 21708
|
|
Posted: Tue Aug 24, 2010 11:33 am |
|
|
Quote: | I am using 128k external parallel ram (AS6C1008) with 18f8722. |
The 18F8722 has built-in hardware support for an external parallel ram.
You should study how to do it that way.
From the 18F8722 data sheet:
Quote: |
7.0 EXTERNAL MEMORY BUS
The External Memory Bus (EMB) allows the device to
access external memory devices (such as Flash,
EPROM, SRAM, etc.) as program or data memory. It
supports both 8-bit and 16-bit Data Width modes and
four address widths from 8 to 20 bits.
Note: The External Memory Bus is not imple-mented
on PIC18F6527/6622/6627/6722
(64-pin) devices.
7.2.1 21-BIT ADDRESSING
As an extension of 20-bit address width operation, the
External Memory Bus can also fully address a 2 Mbyte
memory space. |
|
|
![](templates/subSilver/images/spacer.gif) |
assaad
Joined: 09 Dec 2009 Posts: 37
|
|
Posted: Thu Aug 26, 2010 8:53 am |
|
|
Thank you.
It is ok now, there was problem in the address.
I could not use the hardware one because I am using the ports for other issue. Software one save pin for me. However its ok now. |
|
![](templates/subSilver/images/spacer.gif) |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|