CCS C Software and Maintenance Offers
FAQFAQ   FAQForum Help   FAQOfficial CCS Support   SearchSearch  RegisterRegister 

ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to support@ccsinfo.com
Using software serial port causes output pin to stop working

 
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion
View previous topic :: View next topic  
Author Message
Dutch2



Joined: 05 Oct 2007
Posts: 8

View user's profile Send private message Visit poster's website

Using software serial port causes output pin to stop working
PostPosted: Fri Feb 01, 2008 5:03 pm     Reply with quote
My project needs to communicate on a LIN bus. I hooked the (home grown) driver to the hardware UART pins on my 16F887 but I forgot that my driver inverts so I fixed it in software by switching to a software UART and using the INVERT function:

#use rs232(baud=9600, xmit=PIN_C6, rcv=PIN_C7, stream=LIN, force_sw, invert)

#use fast_io(C)

set_tris_c(0b10000000);

Another pin on the same port (C1) controls a indicator light.

Code:
  //fputc(0x00,LIN); 
  while (TRUE) {
    output_toggle(Indicator);
    delay_ms(100);
  }



I wrote this simple test program after my main program failed when I started using the LIN bus.

Basically the loop flashes the indicator as long as the fputc is commented out. As soon as I uncomment it, the indicator stops flashing.

Any idea what I'm doing wrong here?

Thanks in advance,

D2.
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Fri Feb 01, 2008 5:53 pm     Reply with quote
Quote:
I wrote this simple test program.

Those are actually code fragments. Post a complete test program.
Here's an example:
http://www.ccsinfo.com/forum/viewtopic.php?t=32831&start=4
It has all statements that are needed to compile it: #include, #fuses,
#use, and a main(), and the minimum lines of code needed to test
the desired feature or problem.
Dutch2



Joined: 05 Oct 2007
Posts: 8

View user's profile Send private message Visit poster's website

PostPosted: Fri Feb 01, 2008 6:23 pm     Reply with quote
Code:
#include <16f887.h>
#fuses INTRC_IO,WDT,MCLR,NOPROTECT,BROWNOUT,BORV40,NOLVP
#device ADC=10
#use delay(internal=4M)
#use rs232(baud=9600, xmit=PIN_C6, rcv=PIN_C7, stream=LIN, force_sw, invert)
#use fast_io(A)
#use fast_io(B)
#use fast_io(C)
#use fast_io(D)
#use fast_io(E)

#define Indicator pin_c1

void init_system (void) {
   set_tris_a(0b11111111);              //Port a i/o
   set_tris_b(0b11111111);              //Port b i/o
   set_tris_c(0b10000000);              //Port c i/o
   set_tris_d(0b10000000);              //Port d i/o
   set_tris_e(0b00001111);              //Port e i/o
  output_c(0b10000000);
  output_d(0b10110000);
   setup_adc(ADC_CLOCK_DIV_8);
   setup_adc_ports(0x300FF);
   setup_wdt(WDT_144MS);

}

void main(void) {
  init_system();
  //fputc(0x00,LIN);
  while (True) {
    output_toggle(Indicator);
    delay_ms(100);
    restart_wdt();
   }
}


PCM version 4.065
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Fri Feb 01, 2008 6:41 pm     Reply with quote
Try a more simple test program:
Code:
#include <16F887.h>
#fuses INTRC_IO,MCLR,NOPROTECT,BROWNOUT,BORV40,NOLVP
#use delay(internal=4M)
#use rs232(baud=9600, xmit=PIN_C6, rcv=PIN_C7, stream=LIN, force_sw, invert)

#define INDICATOR PIN_C1

//============================
void main(void)
{
fputc(0x00, LIN);

while(True)
  {
   output_toggle(Indicator);
   delay_ms(100);
  }
}
Dutch2



Joined: 05 Oct 2007
Posts: 8

View user's profile Send private message Visit poster's website

PostPosted: Fri Feb 01, 2008 6:58 pm     Reply with quote
Yep, that works. Any idea what is causing this?

Thanks,

D2.
PCM programmer



Joined: 06 Sep 2003
Posts: 21708

View user's profile Send private message

PostPosted: Fri Feb 01, 2008 7:04 pm     Reply with quote
Add the lines of code back in, one or two at a time, until it fails.
See which line causes the failure.
Dutch2



Joined: 05 Oct 2007
Posts: 8

View user's profile Send private message Visit poster's website

PostPosted: Sat Feb 02, 2008 10:21 am     Reply with quote
Whenever I use fast_io for port C it stops working.

I checked another project where I used a software serial port on port B where I did not encounter this issue.
Code:
#include <16f876a.h>
#fuses HS,NOWDT,NOPROTECT,NOBROWNOUT,NOLVP
#device ADC=10
#use delay(clock=16000000)
#use rs232(baud=19200, xmit=PIN_C6, rcv=PIN_C7, stream=PC)
#use rs232(baud=19200, xmit=PIN_B4, rcv=PIN_B5, stream=LIN, invert)
#use fast_io(b)
#use fast_io(c)

Any ideas why I am seeing this issue now?

D2.
Ttelmah
Guest
PostPosted: Sat Feb 02, 2008 11:17 am     Reply with quote
Because on that project you were using the hardware serial on port C.

Best Wishes
Display posts from previous:   
Post new topic   Reply to topic    CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group