![](templates/subSilver/images/CCSLogo.jpg) |
![CCS C Software and Maintenance Offers](templates/subSilver/images/forumAd6.jpg) |
View previous topic :: View next topic |
Author |
Message |
mworks
Joined: 29 May 2007 Posts: 3
|
Need help with arrays |
Posted: Tue May 29, 2007 7:57 pm |
|
|
I'm trying to write a program that will send out a stream of pulses based on values stored in an array. The lines at the very end are so I can distinguish the pulse start/end on a logic analyzer.
I tried to write it using the array values directly like if the array contained the value I[5] = 300, the I would use delay_ms(I[5]);
However that refused to work, the pic seemed to ignore it and use a value of 20us for the pulse.
so I wrote the code below.
It works except that if I change the line:
While(z!=14) to read While(z!=15) the program ceases to work.
It seems if I try to access anything above 14 in the array the program fails to run.
I'm using tiny bootloader , could this be the problem ?
I'm new at this so any pointers are very welcome.
Code: |
#include <16F88.h>
#device adc=8
#build( reset=0x1, interrupt=0x5)
#ORG 0x0F00, 0x0FFF {}
#FUSES NOWDT //No Watch Dog Timer
#FUSES HS //High speed Osc (> 4mhz)
#FUSES NOPUT //No Power Up Timer
#FUSES NOMCLR //Master Clear pin used for I/O
#FUSES NOBROWNOUT //No brownout reset
#FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O
#FUSES NOCPD //No EE protection
#FUSES NOWRT //Program memory not write protected
#FUSES NODEBUG //No Debug mode for ICD
#FUSES NOPROTECT //Code not protected from reading
#FUSES NOFCMEN //Fail-safe clock monitor disabled
#FUSES NOIESO //Internal External Switch Over mode disabled
#use delay(clock=20000000)
#use rs232(baud=9600,parity=N,xmit=PIN_A3,rcv=PIN_A2,bits=8)
void main()
{
int y;
int z=0;
int dly[17] = {1,2,1,2,1,2,1,2,1,2,1,2,1,2,1,3,3};
while(TRUE)
{
While(z!=14)
{
y=dly[z];
output_low(PIN_B0);
If (y==1)
{
delay_us(585);
}
If (y==2)
{
delay_us(444);
}
If (y==3)
{
delay_ms(1.5);
}
z=z+1;
y=dly[z];
output_high(PIN_B0);
If (y==1)
{
delay_us(585);
}
If (y==2)
{
delay_us(444);
}
If (y==3)
{
delay_ms(1.5);
}
z=z+1;
}
z=0;
output_low(PIN_B0);
delay_us(50);
output_high(PIN_B0);
delay_us(50);
}
}
|
|
|
![](templates/subSilver/images/spacer.gif) |
PCM programmer
Joined: 06 Sep 2003 Posts: 21708
|
|
Posted: Tue May 29, 2007 11:18 pm |
|
|
Download the latest compiler manual.
http://www.ccsinfo.com/downloads/ccs_c_manual.pdf
Read the section on how to use the delay_ms() function. What does
it say about the parameter that may be passed to the function ? |
|
![](templates/subSilver/images/spacer.gif) |
inservi
Joined: 13 May 2007 Posts: 128
|
|
Posted: Wed May 30, 2007 1:37 am |
|
|
Hello,
int dly[17] create a 17 element array. subscript are from 0 to 16.
While(z!=14)
..
z=z+1 ( now z=15 )
..
z=z+1 ( now z=16)
..
If you start with 15 at the second z++, dly[z]; point to an unknown value probably not 1,2 or 3 then the last pulse is very short.
If the version CCS version 4 is not solving your problem, make a function
witch receive an argument and make the calculated number of delay_ necessary.
dro _________________ in médio virtus |
|
![](templates/subSilver/images/spacer.gif) |
mworks
Joined: 29 May 2007 Posts: 3
|
|
Posted: Wed May 30, 2007 7:36 am |
|
|
Thanks for pointing that out.
That was the problem.
I'm trying to learn C and Pics in general at the same time and while its fun , its also trying at times. ![Laughing](images/smiles/icon_lol.gif) |
|
![](templates/subSilver/images/spacer.gif) |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|