![](templates/subSilver/images/CCSLogo.jpg) |
![CCS C Software and Maintenance Offers](templates/subSilver/images/forumAd6.jpg) |
View previous topic :: View next topic |
Author |
Message |
Guest
|
IO Problem, Cannot Read Inputs |
Posted: Tue Sep 20, 2005 1:45 pm |
|
|
Im not sure what the problem is, but I cannot seem to read my IO pins.
I am using the PIC18F8490. I have an LCD connected (which I know works). I am just trying to change whats displayed to corresond to switch settings. It never changes. I have external pullups on all of the input pins. Any ideas?
Code: |
#include "lcdboard.h"
void main() {
PreLaunch();
Configure_IO();
Configure_Units(); // Read all switch setting, set defaults
while(1){
testIO();
}
}
void PreLaunch(){
setup_oscillator(OSC_31KHZ|OSC_INTRC);
setup_adc_ports(NO_ANALOGS|VSS_VDD);
setup_adc(ADC_OFF|ADC_TAD_MUL_0);
setup_timer_0(RTCC_INTERNAL);
setup_timer_1(T1_DISABLED);
setup_timer_2(T2_DISABLED,0,1);
setup_timer_3(T3_DISABLED|T3_DIV_BY_1);
setup_ccp1(CCP_OFF);
setup_ccp2(CCP_OFF);
setup_comparator(NC_NC_NC_NC);
setup_vref(FALSE);
setup_spi(SPI_SLAVE);
setup_low_volt_detect(FALSE);
setup_lcd(0b10001001,0b01110000);
}
void Configure_IO() {
Set_TRIS_B(0x00);
Set_TRIS_C(0x00);
}
void TestIO(){
int value1 = 0;
int value2 = 0;
if (DIP1 == 0)
value1+=1;
if (DIP2 == 0)
value1+=2;
if (DIP3 == 0)
value1+=4;
if (DIP4 == 0)
value1+=8;
if (DIP5 == 0)
value1+=16;
if (DIP6 == 0)
value1+=32;
if (value1 > 29){
lcd_symbol(Digit_Map[3],DIGIT5);
lcd_symbol(Digit_Map[value1-30],DIGIT4);
}
else if (value1 > 19){
lcd_symbol(Digit_Map[2],DIGIT5);
lcd_symbol(Digit_Map[value1-20],DIGIT4);
}
else if (value1 > 9){
lcd_symbol(Digit_Map[1],DIGIT5);
lcd_symbol(Digit_Map[value1-10],DIGIT4);
}
else {
lcd_symbol(Digit_Map[value1],DIGIT4);
}
if (SW1 == 0)
lcd_symbol(Digit_Map[1],DIGIT8);
if (SW2 == 0)
lcd_symbol(Digit_Map[2],DIGIT8);
if (SW3 == 0)
lcd_symbol(Digit_Map[3],DIGIT5);
}
|
Heres part of the .h file
Code: |
#include <18F8490.h>
#device adc=10
#FUSES NOWDT //Watch Dog Timer uses 1:32 Postscale
#FUSES INTRC_IO //Internal RC Osc, no CLKOUT
#FUSES NOPROTECT //Code not protected from reading
#FUSES NOBROWNOUT //No brownout reset
#FUSES BORV28 //Brownout reset at 2.8V
#FUSES NOPUT //No Power Up Timer
#FUSES NOIESO //Internal External Switch Over mode disabled
#FUSES STVREN //Stack full/underflow will cause reset
#FUSES NODEBUG //No Debug mode for ICD
#FUSES NOFCMEN //Fail-safe clock monitor disabled
#FUSES NOMCLR //Master Clear pin enabled
#FUSES LPT1OSC //Timer1 configured for low-power operation
#FUSES NOXINST //Extended set extension and Indexed Addressing mode disabled (Legacy mode)
#use delay(clock=32000)
#define SW1 PIN_B7
#define SW2 PIN_B6
#define SW3 PIN_B5
#define DIP1 PIN_B0
#define DIP2 PIN_B1
#define DIP3 PIN_B2
#define DIP4 PIN_B3
#define DIP5 PIN_B4
#define DIP6 PIN_C2
|
|
|
![](templates/subSilver/images/spacer.gif) |
newguy
Joined: 24 Jun 2004 Posts: 1903
|
|
Posted: Tue Sep 20, 2005 1:52 pm |
|
|
You have the tris set wrong. 0 = output, 1 = input. |
|
![](templates/subSilver/images/spacer.gif) |
Mark
Joined: 07 Sep 2003 Posts: 2838 Location: Atlanta, GA
|
|
Posted: Tue Sep 20, 2005 1:59 pm |
|
|
PIN_B7 is #defined as a number
Code: | #define PIN_B7 31759
|
that means something to CCS specific functions.
In your code:
would be
See the problem yet? You need to define DIP1 as portb.7 where you define portb as a variabe at the location of portb. Another option is to use the CCS function input(DIP1).
Also, if you handle the var yourself, remember to set the tris correctly (1 for an input). If you use standard_io and the CCS function, the Compiler will handle the tris for you. |
|
![](templates/subSilver/images/spacer.gif) |
Guest
|
|
Posted: Tue Sep 20, 2005 2:29 pm |
|
|
Thanks Guys, works now. |
|
![](templates/subSilver/images/spacer.gif) |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|